參數資料
型號： PCD5042HZ
廠商： NXP SEMICONDUCTORS
元件分類： 無繩電話/電話
英文描述： DECT burst mode controller
中文描述： TELECOM, CORDLESS, BURST MODE CONTROLLER, PQFP80
文件頁數： 20/28頁
文件大小： 134K
代理商： PCD5042HZ
1996 Oct 31
20
Philips Semiconductors
Objective specification
DECT burst mode controller
PCD5042
Notes to the characteristics
1.
V
DD
= 3.0 V; f
clk
=13.824 MHz; no external load; one speech link active (under typical conditions).
2.
V
DD
= 3.0 V; f
clk
=13.824 MHz; no external load; after reset.
3.
Maximum differential non-linearity at supply voltage 5.5 V and V
REF
= 1 V.
4.
Supply current I
DD(stb)(comp)
flows when COMP_NE is HIGH.
Supply current I
DD(idle)(comp)
flows when the comparator is in active mode (COMP_NE is LOW). It is the DC current
of the comparator when it is not switching, and V(COMP_INP) < V(COMP_INM).
The active mode supply current I
DD(1MHz)
includes the output pulse rate of 1 MHz.
5.
For input pins COMP_INP, COMP_INM, COMP_NE.
6.
For input pin COMP_NE.
7.
The minimum input common mode voltage will be measured at DC levels with, COMP_INM at 1 V DC
±
30 mV.
The same goes for the maximum input common mode voltage at (V
DD
0.5V).
8.
These values are not tested in production, and are based upon theoretical estimates and laboratory tests.
9.
The propagation delay t
pd
is measured from the time the differential input voltage equals the offset voltage, to the
50% point of the output transition. The initial differential input voltage is 100 mV and the propagation delay is
specified for an input overdrive of 30 mV, and a load capacitance of 50 pF. t
pd
is valid for both the positive and
negative going output transition. The maximum value is valid for the total ranges of temperature, supply voltage and
common mode input voltage. The worst case operation conditions are at the minimum supply voltage, the lowest
operating temperature and the minimum input common mode voltage. The delay difference
t
pd
gives the difference
between t
pd
for the rising output transition and t
pd
for the falling output transition and is valid for all operating
conditions. The test method to check the maximum delay difference is by measuring the RMS voltage of the output
signal.
相關PDF資料
PDF描述
PCD5042 DECT burst mode controller
PCD5043 DECT burst mode controller
PCD5043H DECT burst mode controller
PCD5091HZ DECT baseband controller
PCD5091 DECT baseband controller
相關代理商/技術參數
參數描述
PCD5043 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT burst mode controller
PCD5043H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT burst mode controller
PCD5071 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM
PCD5090 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT baseband controllers
PCD5090H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DECT baseband controllers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*