- 您現在的位置：買賣IC網 > PDF目錄382380 > PCD3359AT (NXP SEMICONDUCTORS) 8-bit microcontroller with DTMF generator and 128 bytes EEPROM PDF資料下載
參數資料
| 型號： | PCD3359AT |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-bit microcontroller with DTMF generator and 128 bytes EEPROM |
| 中文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDSO28 |
| 封裝： | 7.50 MM, PLASTIC, SO-28 |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 165K |
| 代理商： | PCD3359AT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
1998 May 11
16
Philips Semiconductors
Product specification
8-bit microcontroller with DTMF
generator and 128 bytes EEPROM
PCD3359A
Table 18
Page setup; preset
Table 19
Page setup; auto-incrementing
7.5.2
R
EAD BYTE
Since ADDR auto-increments after a read cycle regardless
of the page boundary, successive bytes can efficiently be
read by repeating the last instruction.
Table 20
Read byte
7.5.3
W
RITE PAGE
The write cycle performs a logical OR between the data in
the EEPROM latches and that in the addressed EEPROM
page. To actually copy the data from the EEPROM
latches, the corresponding bytes in the page should
previously have been erased.
INSTRUCTION
RESULT
MOV A, #addr
MOV ADDR, A
MOV A, #data
MOV DATR, A
address of EEPROM latch
send address to ADDR
load write, erase/write or erase data
send data to addressed EEPROM
latch
INSTRUCTION
RESULT
MOV A, #MC2
MOV EPCR, A
MOV A, #baddr
increment mode control word
select increment mode
EEPROM Latch 0 address
(AD0 = AD1 = 0)
send EEPROM Latch 0 address to
ADDR
load 1
st
byte from Register 0
send 1
st
byte to EEPROM Latch 0
load 2
nd
byte from Register 1
send 2
nd
byte to EEPROM Latch 1
load 3
rd
byte from Register 2
send 3
rd
byte to EEPROM Latch 2
load 4
th
byte from Register 3
send 4
th
byte to EEPROM Latch 3
MOV ADDR, A
MOV A, R0
MOV DATR, A
MOV A, R1
MOV DATR, A
MOV A, R2
MOV DATR, A
MOV A, R3
MOV DATR, A
INSTRUCTION
RESULT
MOV A, #RDADDR load read address
MOV ADDR, A
MOV A, DATR
send address to ADDR
read EEPROM data
The EEPROM latches are preset as described in
Section 7.5.1. The actual transfer to the EEPROM is then
performed as shown in Table 21.
The last instruction also starts Timer 2. The data in the
EEPROM latches are ORed with that in the corresponding
page bytes within 5 ms. A single-byte write is simply a
special case of ‘write page’.
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM Latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by bits AD2
to AD6) and to EEPROM Latch 0 (by bits AD0 and AD1).
This allows efficient coding of multi-page write operations.
Table 21
Write page
7.5.4
E
RASE
/
WRITE PAGE
The EEPROM latches are preset as described in
Section 7.5.1. The page byte corresponding to the
asserted flags (among F0 to F3) are erased and re-written
with the contents of the respective EEPROM latches.
The last instruction also starts Timer 2. Erasure takes
5 ms upon which Timer Register T2 reloads for another
5 ms cycle for writing. The top cycles together take 10 ms.
A single-byte erase/write is simply a special event of
‘erase/write page’.
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by AD2 to
AD6) and to EEPROM latch 0 (by AD0 and AD1).
This allows efficient coding of multi-page erase/write
operations.
Table 22
Erase/write page
INSTRUCTION
RESULT
MOV A, #EWP + MC2
MOV EPCR, A
‘write page’ control word
start ‘write page’ cycle
INSTRUCTION
RESULT
MOV A, #EWP + MC3
MOV EPCR, A
‘erase/write page’ control word
start ‘erase/write page’ cycle
相關PDF資料 |
PDF描述 |
|---|---|
| PCD3360 | Programmable multi-tone telephone ringer |
| PCD3360P | Programmable multi-tone telephone ringer |
| PCD3360T | Programmable multi-tone telephone ringer |
| PCD4440T | Analog voice scrambler/descrambler |
| PCD5003A | Enhanced Pager Decoder for POCSAG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD3360 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable multi-tone telephone ringer |
| PCD3360P | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable multi-tone telephone ringer |
| PCD3360T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable multi-tone telephone ringer |
| PCD33XXA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-Bit telecom microcontrollers |
| PCD33XXFAMILY | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
發布緊急采購，3分鐘左右您將得到回復。