參數(shù)資料
型號: PCD3316T
廠商: NXP SEMICONDUCTORS
元件分類: 通信及網絡
英文描述: Caller-ID on Call Waiting CIDCW receiver
中文描述: SPECIALTY TELECOM CIRCUIT, PDSO16
封裝: 7.50 MM, PLASTIC, SOT-162-1, SO-16
文件頁數(shù): 6/30頁
文件大小: 534K
代理商: PCD3316T
Philips Semiconductors
PCD3316
CIDCW receiver
Product specification
11 March 1999
6 of 30
9397 750 04824
Philips Electronics N.V. 1999. All rights reserved.
voltage generator. The voltage levels on the two polarity comparator inputs, POL0
and POL1, are compared with the reference voltage V
ref
. If POL0 < V
ref
or
POL1 > V
ref
, POL0 and POL1 (Status register, bit 7 and 6) are set respectively and
reset if POL0 > V
ref
and POL1 < V
ref
. Every time the POL0 status bit changes from
logic 1 to logic 0, a POL0 interrupt is generated. Every time the POL1 status bit
changes from logic 0 to logic 1, a POL1 interrupt is generated.
The FSK-OVR Error bit (Status register, bit 3) indicates that a previous byte is lost
due to an overrun. The FSK-FRM Error bit (Status register, bit 2) indicates an
incorrect start- or stop-bit. These frame errors indicate that there are synchronization
problems. The on-chip level detector can be used to detect a carrier loss during FSK
transmission. FSK data can be rejected when the signal level is below the reference
level, this to avoid that noise is interpreted as data (Interrupt register, bit 4 is logic 1).
7.4 Ring or polarity change detector
For ring and polarity change detection two comparators are available in the
The period time of a POL1-POL0-POL1 sequence is available in the Ringer period
register. It is preset to 255 on power-on and updated every time a POL1 interrupt is
generated. The sequence is:
1. Power-on: Ringer period register = 255
2. First POL1 interrupt: Ringer period register = 255
3. First POL1 interrupt after a POL0 interrupt: Ringer period register = new time
4. First POL1 interrupt after more than
255
2048
s: Ringer period register = 255.
The period is given in multiples of
1
2048
s. The maximum value is 255.
The POL1-POL0-POL1 sequence is recognized when one or more POL1 interrupts
are generated followed by one or more POL0 interrupts, followed by a POL1 interrupt.
The 32.768 kHz clock is needed for the generation of a polarity interrupt.
7.5 Low battery detection
The low battery voltage detection input (pin LOWBAT) is connected to the positive
input of a comparator. The negative input is connected to the internal reference
voltage. If the voltage on the LOWBAT input pin is less than the reference voltage V
ref
,
the LOW-BAT Indication (Status register, bit 5) is set. If the LOWBAT input rises
above V
ref
again, the LOW-BAT Indication is cleared.
Fig 4.
IRQ generation after reading a valid data byte.
handbook, full pagewidth
MBH981
START
IRQ
read by
serial interface
D0
D1
D2
D3
D4
D5
D6
D7
STOP
相關PDF資料
PDF描述
PCD3330-1 Multistandard repertory dialler/ringer with EEPROM
PCD3330-1P Multistandard repertory dialler/ringer with EEPROM
PCD3330-1T Multistandard repertory dialler/ringer with EEPROM
PCD3354AH 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM
PCA3354CH 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM
相關代理商/技術參數(shù)
參數(shù)描述
PCD3316TD-T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Caller Number ID Circuit
PCD3320CD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Telephone Dialer
PCD3321CD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Telephone Dialer
PCD3322CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Telephone Dialer
PCD3324CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Pulse Telephone Dialer