- 您現在的位置：買賣IC網 > PDF目錄369949 > PCA9561 (NXP Semiconductors N.V.) Quad 6-bit multiplexed I2C EEPROM DIP switch PDF資料下載
參數資料
| 型號： | PCA9561 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Quad 6-bit multiplexed I2C EEPROM DIP switch |
| 中文描述： | 四6位多路復用的I2C EEPROM的DIP開關 |
| 文件頁數： | 6/17頁 |
| 文件大小： | 111K |
| 代理商： | PCA9561 |
Philips Semiconductors
Product data
PCA9561
Quad 6-bit multiplexed I
2
C EEPROM DIP switch
2003 Jun 27
6
EXTERNAL CONTROL SIGNALS
The Write Protect (WP) input is used to control the ability to write the content of the non-volatile registers. If the WP signal is logic 0, the I
2
C-bus
will be able to write the contents of the non-volatile registers. If the WP signal is logic 1, data will not be allowed to be written into the
non-volatile registers. In this case, the slave address and the command code will be acknowledged but the following data bytes will not be
acknowledged and the EEPROM is not updated.
The factory default for the contents of the non-volatile register are all logic 0. These stored values can be read or written using the I
2
C-bus
(described in the next section).
The WP, MUX_IN*, and MUX_SELECT signals have internal pull-up resistors. See the DC and AC Characteristics for hysteresis and signal
spike suppression figures.
Function Table
1
WP
MUX_SELECT
COMMANDS
0
X
Write to the non-volatile registers through I
2
C-bus allowed
Write to the non-volatile registers through I
2
C-bus not allowed
1
X
X
0
MUX_OUT from EEPROM byte 0-3
(EEPROM selected through I
2
C - see Table 2)
X
1
MUX_OUT from MUX_IN inputs
NOTE:
1. This table is valid when not overridden by I
2
C control register.
POWER-ON RESET (POR)
When power is applied to V
DD
, an internal power-on reset holds the PCA9561 in a reset state until V
DD
has reached V
POR
. At that point, the
reset condition is released and the PCA9561 volatile registers and state machine will initialize to their default states.
The MUX_OUT pin values depend on the MUX_SELECT logic level:
-
if MUX_SELECT = 0, the MUX_OUT pin output values will equal the previously stored EEPROM byte 0 values regardless of the last
non-volative EEPROM byte selected by the command byte prior to power down.
-
if MUX_SELECT = 1, the MUX_OUT output values will equal the MUX_IN pin input values as shown in the Function Table.
相關PDF資料 |
PDF描述 |
|---|---|
| PCB2421 | 1K dual mode serial EEPROM |
| PCB2421P | 1K dual mode serial EEPROM |
| PCB2421T | 1K dual mode serial EEPROM |
| PCD3344A | 8-BIT MICROCONTROLLER WITH DTMF GENERATOR |
| PCD3349AT | 8-BIT MICROCONTROLLER WITH DTMF GENERATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9561D | 功能描述:電可擦除可編程只讀存儲器 QUAD 6-BT MULTIPLEX I2C 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9561D,112 | 功能描述:多路器開關 IC QUAD 6-BT MULTIPLEX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9561D,118 | 功能描述:多路器開關 IC QUAD 6-BT MULTIPLEX RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| PCA9561D-T | 功能描述:電可擦除可編程只讀存儲器 QUAD 6-BT MULTIPLEX I2C 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| PCA9561PW | 功能描述:電可擦除可編程只讀存儲器 QUAD 6-BT MULTIPLEX I2C 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。