Table 41 lists major changes " />
參數資料
型號： PC56F8006VLF
廠商： Freescale Semiconductor
文件頁數： 89/106頁
文件大?。?/td> 0K
描述： DSP 16BIT 48-LQFP
標準包裝： 250
系列： 56F8xxx
核心處理器： 56800
芯體尺寸： 16-位
速度： 32MHz
連通性： I²C，LIN，SCI，SPI
外圍設備： LVD，POR，PWM，WDT
輸入/輸出數： 40
程序存儲器容量： 16KB（8K x 16）
程序存儲器類型： 閃存
RAM 容量： 1K x 16
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 3.6 V
數據轉換器： A/D 24x12b
振蕩器型： 內部
工作溫度： -40°C ~ 105°C
封裝/外殼： 48-LQFP
包裝： 托盤
Revision History
MC56F8006/MC56F8002 Digital Signal Controller, Rev. 4
Freescale Semiconductor
83
11
Revision History
Table 41 lists major changes between versions of the MC56F8006 document.
Appendix A
Interrupt Vector Table
Table 43 provides the 56F8006/56F8002’s reset and interrupt priority structure, including on-chip peripherals. The table is
organized with higher-priority vectors at the top and lower-priority interrupts lower in the table. As indicated, the priority of an
interrupt can be assigned to different levels, allowing some control over interrupt priorities. All level 3 interrupts are serviced
before level 2 and so on. For a selected priority level, the lowest vector number has the highest priority.
The location of the vector table is determined by the vector base address (VBA). Please see the MC56F8006 Peripheral
Reference Manual for detail.
By default, the chip reset address and COP reset address correspond to vector 0 and 1 of the interrupt vector table. In these
instances, the first two locations in the vector table must contain branch or JMP instructions. All other entries must contain JSR
instructions.
Table 41. Changes Between Revisions 2 and 3
Location
Description
Introduction on page 1
Added part marking for devices covered by this document
Updated routing details for ANB24 and ANB25
Removed row about open drain mode (GPIO supports only push-pull mode)
Updated specifications for low-voltage detection threshold (high and low range) and
low-voltage warning threshold
Updated all Supply Current Consumption specifications
Updated ROSC variation over temperature specifications (both ranges)
Removed I2C fast mode specifications and footnote about setup time if the TX FIFO
is empty (fast mode and FIFO not supported)
Appendix B on page 86
Added note explaining ADC and GPIO naming conventions
For I2C_SMB_CSR, clarified that bits 7 and 6 are reserved
Table 42. Changes Between Revisions 3 and 4
Location
Description
Throughout document.
Added information for 32-pin PSDIP device and devices with temperature range
from –40
C to + 125 C.
相關PDF資料
PDF描述
PK10N512VLK100 IC ARM CORTEX MCU 512K 80-LQFP
1061541630 ADPT OPT SINGLEMODE LC-LC BLUE
1061541100 ADPT OPT SINGLEMODE SC-SC BLUE
PK60N512VLQ100 IC ARM CORTEX MCU 512K 144-LQFP
PK60N512VMD100 IC ARM CORTEX MCU 512K 144-MAP
相關代理商/技術參數
參數描述
PC56F8006VWL 功能描述:數字信號處理器和控制器 - DSP, DSC 16-BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
PC56F8023VLC 制造商:Freescale Semiconductor 功能描述:16 BIT DSPHC - Trays
PC56F8025VLD 制造商:Freescale Semiconductor 功能描述:16-BIT 56F8XXX CISC 32KB FLASH 3.3V 44-PIN LQFP TRAY - Trays
PC56F8037VLH 制造商:Freescale Semiconductor 功能描述:
PC56F8245VLD 制造商:Freescale Semiconductor 功能描述:PC56F8245VLD - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*