- 您現在的位置：買賣IC網 > PDF目錄383737 > PC33926PNB (飛思卡爾半導體(中國)有限公司) 5.0 A Throttle Control H-Bridge PDF資料下載
參數資料
| 型號： | PC33926PNB |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 5.0 A Throttle Control H-Bridge |
| 中文描述： | 5.0甲節氣門控制H橋 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 378K |
| 代理商： | PC33926PNB |
Analog Integrated Circuit Device Data
Freescale Semiconductor
11
33926
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
Numerous protection and operational features (speed,
torque, direction, dynamic breaking, PWM control, and
closed-loop control) make the 33926 a very attractive, cost-
effective solution for controlling a broad range of small DC
motors. The 33926 outputs are capable of supporting peak
DC load currents of up to 5.0 A from a 28 V
PWR
source. An
internal charge pump and gate drive circuitry are provided
that can support external PWM frequencies up to 20 kHz.
The 33926 has an analog feedback (current mirror) output
pin (the FB pin) that provides a constant-current source
ratioed to the active high-side
MOSFETs
’ current. This can be
used to provide “real time” monitoring of output current to
facilitate closed-loop operation for motor speed/torque
control, or for the detection of open load conditions.
Two independent inputs, IN1 and IN2, provide control of
the two totem-pole half-bridge outputs. An input invert, INV,
changes IN1 and IN2 to LOW = true logic. Two different
output slew rates are selectable via the SLEW input. Two
independent disable inputs, D1 and
D2
, provide the means to
force the H-Bridge outputs to a high impedance state (all H-
Bridge switches OFF). An EN pin controls an enable function
that allows the IC to be placed in a power-conserving Sleep
mode.
The 33926 has Output Current Limiting (via Constant
OFF-Time PWM Current Regulation), Output Short-Circuit
Detection with Latch-OFF, and Overtemperature Detection
with Latch-OFF. Once the device is latched-OFF due to a
fault condition, either of the Disable inputs (D1 or D2), V
PWR
,
or EN must be “toggled” to clear the status flag.
Current limiting (Load Current Regulation) is
accomplished by a constant-OFF time PWM method using
current limit threshold triggering. The current limiting scheme
is unique in that it incorporates a junction temperature-
dependent current limit threshold. This means that the
current limit threshold is “reduced to around 4.2 A” as the
junction temperature increases above 160°C. When the
temperature is above 175°C, overtemperature shutdown
(latch-OFF) will occur. This combination of features allows
the device to continue operating for short periods of time (< 30
seconds) with unexpected loads, while still retaining
adequate protection for both the device and the load.
FUNCTIONAL PIN DESCRIPTION
POWER GROUND AND ANALOG GROUND
(PGND AND AGND)
The power and analog ground pins should be connected
together with a very low impedance connection.
POSITIVE POWER SUPPLY (VPWR)
VPWR pins are the power supply inputs to the device. All
VPWR pins must be connected together on the printed circuit
board with as short as possible traces, offering as low
impedance as possible between pins.
STATUS FLAG (
SF
)
This pin is the device fault status output. This output is an
active LOW open drain structure requiring a pullup resistor to
V
DD
. The maximum V
DD
is < 7.0 V. Refer to
Table 5, Truth
Table
, page
14
for the SF Output status definition.
INPUT INVERT (INV)
The Input Invert Control pin sets IN1 and IN2 to
LOW = TRUE. This is a Schmitt trigger input with
~ 80 μA
sink;
the default condition is non-inverted. If IN1 and IN2 are set so
that the current is being commanded to flow through the load
attached between OUT1 and OUT2, changing the logic level
at INV will have the effect of reversing the direction of current
commanded. Thus, the INV input may be used as a “forward/
reverse” command input. If both IN1 and IN2 are the same
logic level, then changing the logic level at INV will have the
effect of changing the bridge’s output from freewheeling high
to freewheeling low or vice versa.
SLEW RATE (SLEW)
The SLEW pin is the logic input that selects fast or slow
slew rate. Schmitt trigger input with
~ 80 μA
sink so the default
condition is SLOW. When SLEW is set to SLOW, PWM-ing
should be limited to frequencies less than 11 kHz in order to
allow the internal high-side driver circuitry time to fully
enhance the high-side MOSFETs.
INPUT 1,2 AND DISABLE INPUT 1,2
(IN1, IN2, AND D1, D2
)
These pins are input control pins used to control the
outputs. These pins are 3.0 V/ 5.0 V CMOS-compatible
inputs with hysteresis. IN1 and IN2 independently control
OUT1 and OUT2, respectively. D1 and
D2
are
complementary inputs used to tri-state disable the H-Bridge
outputs.
When either D1 or
D2
is SET (D1 = logic HIGH or
D2
= logic LOW) in the disable state, outputs OUT1 and
OUT2 are both tri-state disabled; however, the rest of the
device circuitry is fully operational and the supply
I
PWR(STANDBY)
current is reduced to a few mA. Refer to
Table
3, Static Electrical Characteristics
,
page 6
.
相關PDF資料 |
PDF描述 |
|---|---|
| PC33926PNBR2 | 5.0 A Throttle Control H-Bridge |
| PC33975A | Multiple Switch Detection Interface with Suppressed Wake-Up and 32mA Wetting Current |
| PC33975AEK | Multiple Switch Detection Interface with Suppressed Wake-Up and 32mA Wetting Current |
| PC33975AR2 | Multiple Switch Detection Interface with Suppressed Wake-Up and 32mA Wetting Current |
| PC3S12XEP100J1CAA | Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC33926PNB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:5.0 A Throttle Control H-Bridge |
| PC33926PNBR2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:5.0 A Throttle Control H-Bridge |
| PC33937APEK | 制造商:Freescale Semiconductor 功能描述: |
| PC33972ATEW | 制造商:Freescale Semiconductor 功能描述: |
| PC33975A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multiple Switch Detection Interface with Suppressed Wake-Up and 32mA Wetting Current |
發布緊急采購，3分鐘左右您將得到回復。