參數資料
型號： P82C150AHT
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 22 PIN R/A MALE PRESSFIT ATCA ZONE 1 CON
中文描述： 1 CHANNEL(S), 125K bps, LOCAL AREA NETWORK CONTROLLER, PDSO28
封裝： 7.50 MM, PLASTIC, SO-28
文件頁數： 20/36頁
文件大?。?/td> 209K
代理商： P82C150AHT
1996 Jun 19
20
Philips Semiconductors
Preliminary specification
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
P82C150
7.4
Initialization
7.4.1
I
DENTIFIER PROGRAMMING
Most of the P82C150 identifier bits are fixed. Four bits are
programmable via port pins P3 to P0. All output drivers are
disabled at reset, also P3 to P0. Thus the outputs are
floating unless the input level is defined by external
components to define identifier bits. They are latched at
the end of reset, and P3 to P0 can be used as port pins.
It is not allowed, according to the CAN protocol
specification, that multiple bus nodes transmit the same
identifier bit combination. Therefore a P82C150 must have
one of the 16 possible identifier bit combinations, one that
is not yet occupied.
7.4.2
R
ESET FUNCTION
RST = HIGH disables all output drivers P16 to P0, TX0
and TX1. All I/O Registers are automatically cleared and
set to logic 0. The bit time is set greater than 50
μ
s.
If a particular clock period is necessary, e.g. for a
dedicated DPM output frequency, this can be achieved by
feeding an external clock signal into P0. RST and TEST
must be permanently HIGH for this special mode. A reset
is then performed as usual (RST = HIGH; TEST = LOW).
Table 14
Situation after RESET
7.4.3
B
IT TIME CALIBRATION
The P82C150 must receive at least three messages to
calibrate its bit time after reset or change of bus mode.
The first message is used to detect the bit time length
(rough calibration) between two consecutive falling edges
at the output of the CAN input comparator. Therefore the
bit stream should contain a sequence of ‘1010’.
STATUS BITS
IDENTIFIER BITS
RSTD = 1
EW = 1
BM1 = 0
BM0 = 0
ID.8 equals P3
ID.5 equals P2
ID.4 equals P1
ID.3 equals P0
After rough calibration the P82C150 can receive any valid
CAN message correctly and executes respective
commands without giving an acknowledge. With another
valid CAN message and additionally with one valid
calibration message the P82C150 is fully calibrated and
sends its ‘sign-on’ message. As long as the P82C150 is
fully calibrated the P82C150 acts as an active CAN node.
The P82C150 treats any CAN message (including the
calibration message) as a valid message, when these
messages are terminated by an error passive frame
because of a missing acknowledge. This situation may
occur whenever a host node works together with
P82C150’s and the host node doesn’t receive an
acknowledge as long as the P82C150’s are not fully
calibrated.
7.4.3.1
Sign-on message
This special Data Frame is transmitted once by the
P82C150 after entering the calibrated state. It indicates to
the host node that the P82C150 is ready for transmission.
The sign-on message returns the contents of the Data
Input Register, and can be recognized by the host mode by
checking the RSTD status bit:
Sign-on message RSTD = 1
Other Data Frames RSTD = 0
Note that in the sign-on message the EW bit is logic 1.
Nevertheless the P82C150 status with the error counters
are set to logic 0.
相關PDF資料
PDF描述
P82C605 System Controller
P82C606 System Controller
P82C607 Peripheral IC
P82C611 Micro Channel Bus Interface/Controller
P82C612 Micro Channel Bus Interface/Controller
相關代理商/技術參數
參數描述
P82C201-10 制造商:CHIPS 功能描述: 制造商:CHIP 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC 制造商:CHIPS 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC
P82C201-10 TS89 制造商:TOS 功能描述:82C201-10
P82C201-10-7014-0093 制造商:CHIPS 功能描述:
P82C20110TS89 制造商:TOS 功能描述:82C201-10
P82C206 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NEW ENHANCED AT DATA BOOK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*