參數資料
型號： P82C150
廠商： NXP Semiconductors N.V.
英文描述： CAN Serial Linked I/O device SLIO with digital and analog port functions
中文描述： CAN串行鏈接I / O與數字和模擬接口功能設備SLIO
文件頁數： 19/36頁
文件大?。?/td> 209K
代理商： P82C150
1996 Jun 19
19
Philips Semiconductors
Preliminary specification
CAN Serial Linked I/O device (SLIO) with
digital and analog port functions
P82C150
7.3.7
T
RANSMIT AND RECEIVE LOGIC
The transmit and receive logic stores the destuffed bit
stream which was received or is about to be transmitted.
The incoming Identifier is compared with that of the
P82C150. The content of the message is transferred to the
port logic in case of matching.
At transmission, the message about to be sent is put
together: the Identifier, the status information, the register
address and the content of the addressed register from the
port logic.
7.3.8
B
IT
S
TREAM
P
ROCESSOR AND
E
RROR
M
ANAGEMENT
L
OGIC
The Bit Stream Processor (BSP) is a sequencer to control
the data stream between the transmit/receive logic
(parallel data) and the on-chip CAN transceiver (serial
data). Reception/transmission, bit stuffing/destuffing,
arbitration and error detection, according to CAN protocol
specification version 2.0 A and B (passive), are performed.
Further, automatic re-transmission of corrupted messages
is handled by means of continuously comparing the output
bit stream with the input bit stream. Moreover, the Bit
Stream Processor provides control information to calibrate
the internal bit time.
The Error Management Logic is responsible for the
complete CAN-inherent error management.
7.3.9
O
SCILLATOR AND CALIBRATION
The P82C150 contains an on-chip RC-oscillator. The bit
time is automatically calibrated by messages being
received via CAN-bus. During start-up (after wake-up or
reset) any message is used to calibrate the bit time until
the calibration is sufficient to receive messages correctly.
From this time on, the bit time is calibrated and fine-tuned
by calibration messages with a special Identifier
transmitted by the crystal-controlled host.
Only P82C150 nodes being calibrated by calibration
messages can transmit messages. The first message is
transmitted directly after entering the calibrated state
(‘sign-on’ message). Since the P82C150 is not able to
transmit as long as the bit time is not calibrated, it cannot
wake-up other CAN nodes via the bus line. Hence to keep
the network alive, the calibration message must be
transmitted regularly by a crystal-controlled (host) node
with a maximum repetition period of 8192 bit (bit length
measured by the 82C150). It is recommended to select a
repetition period between 3800 and maximum 8000 bit
times.
7.3.10
C
ALIBRATION MESSAGE
The calibration message has to meet the following
requirements
Transmitted by a crystal-controlled node (host node)
Identifier: 000 1010 1010 (1 = recessive; 0 = dominant)
RTR bit: 0
Allowed control field: DLC = 2 to 8
The first recessive to dominant transition after the
control field must be followed by another recessive to
dominant transition in a distance of exactly 32 bit (stuff
bits included).
Example of a suitable calibration message (there are
others using different data bytes; see Table 13):
Data length code: 0010
1st data byte: 1010 1010 (AAH)
2nd data byte: 0000 0100 (04H).
Table 13
Example of a suitable calibration message
The two important 1/0 transitions are marked by underlines; see note 1.
Note
1.
I = stuff bit
(recessive); the total length is 67 bit from start-of-frame to end-of-intermission.
SOF
ARBITRATION FIELD
CONTROL
FIELD
DATA BYTE 1
DATA BYTE 2
CRC FIELD
0
000 1010 1010 0
000
I
010
1010 1010
0000
I
0100
000
I
0 1011 1000 00
I
0
相關PDF資料
PDF描述
P82C150AFT CAN Serial Linked I/O device SLIO with digital and analog port functions
P82C150AHT 22 PIN R/A MALE PRESSFIT ATCA ZONE 1 CON
P82C605 System Controller
P82C606 System Controller
P82C607 Peripheral IC
相關代理商/技術參數
參數描述
P82C150AFT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CAN Serial Linked I/O device SLIO with digital and analog port functions
P82C150AHT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CAN Serial Linked I/O device SLIO with digital and analog port functions
P82C201-10 制造商:CHIPS 功能描述: 制造商:CHIP 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC 制造商:CHIPS 功能描述:SYSTEM CONTROLLER, 84 Pin, PLCC
P82C201-10 TS89 制造商:TOS 功能描述:82C201-10
P82C201-10-7014-0093 制造商:CHIPS 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*