- 您現在的位置：買賣IC網 > PDF目錄6168 > OPA567AIRHGT (Texas Instruments)IC OPAMP GP R-R 1.2MHZ 12VQFN PDF資料下載
參數資料
| 型號： | OPA567AIRHGT |
| 廠商： | Texas Instruments |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP R-R 1.2MHZ 12VQFN |
| 標準包裝： | 1 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1.2 V/µs |
| 增益帶寬積： | 1.2MHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 9mA |
| 電流 - 輸出 / 通道： | 2.4A |
| 電壓 - 電源，單路/雙路(±)： | 2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-VQFN 裸露焊盤 |
| 供應商設備封裝： | 12-VQFN-EP（5x5） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 854 (CN2011-ZH PDF) |
| 其它名稱： | 296-18697-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
OPA567
SBOS287A
18
www.ti.com
QFN THERMALLY ENHANCED PACKAGE
The OPA567 uses the QFN-12 package, a thermally-
enhanced package designed to eliminate the use of bulky
heat sinks and slugs traditionally used in thermal packages.
This package can be easily mounted using standard printed
circuit board (PCB) assembly techniques. See QFN/SON
PCB Attachment Application Note (SLUA271) located at
www.ti.com.
The thermal resistance junction-to-ambient (Rθ
JA
) of the QFN
package depends on the PCB layout. Using thermal vias and
wide PCB traces improve thermal resistance. The thermal
pad must be soldered to the PCB. The thermal pad should
either be left floating or connected to V–.
LAYOUT GUIDELINES
The OPA567 is a power amplifier that requires proper layout
for best performance. An example layout is appended to the
end of this datasheet. Refinements to this layout may be
required based on assembly process requirements.
Keep power-supply leads as short as possible. This practice
will keep inductance low and resistive losses at a minimum.
A minimum of 18 gauge wire thickness is recommended for
power- supply leads. The wire length should be less than 8
inches.
Proper power-supply bypassing with low ESR capacitors is
essential to achieve good performance. A parallel combina-
tion of 100nF ceramic and 47
F tantalum bypass capacitors
will provide low impedance over a wide frequency range.
Bypass capacitors should be placed as close as practical to
the power-supply pins of the OPA567.
PCB traces conducting high currents, such as from output to
load or from the power-supply connector to the power-supply
pins of the OPA567 should be kept as wide and short as
possible. This practice will keep inductance low and resistive
losses to a minimum.
The nine holes in the landing pattern for the OPA567 are for
the thermal vias that connect the thermal pad of the OPA567
to the heatsink area on the PCB. All traces conducting high
currents are very wide for lowest inductance and minimal
resistive losses.
相關PDF資料 |
PDF描述 |
|---|---|
| RMCF2010FT36R5 | RES 36.5 OHM 1% 3/4W 2010 SMD |
| RMCF2010FT33K2 | RES 33.2K OHM 1% 3/4W 2010 SMD |
| ESQT-104-03-F-D-310 | CONN SOCKET 8 POS DUAL ROW |
| RMCF2010FT2K49 | RES 2.49K OHM 1% 3/4W 2010 SMD |
| PPTC322LJBN-RC | CONN FEMALE 64POS DL .1" R/A TIN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA567AIRHGT | 制造商:Texas Instruments 功能描述:IC OP-AMP GP R-R 1.2MHZ 12VQFN |
| OPA567AIRHGTG4 | 功能描述:運算放大器 - 運放 Rail-to-Rail I/O 2A Power Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA569 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Power Op Amp. Output Signal Swings Within 200mV of Rails at 2A Output Current |
| OPA569AIDWP | 功能描述:運算放大器 - 運放 2A Pwr Op Amp Rail-To-Rail I/O RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA569AIDWPG4 | 功能描述:運算放大器 - 運放 2A Pwr Op Amp Rail-To-Rail I/O RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。