參數資料
型號： NQ80220
廠商： LSI CORP
元件分類： 網絡接口
英文描述： 100BASE-TX/10BASE-T Ethernet Media Interface Adapter
中文描述： DATACOM, ETHERNET TRANSCEIVER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 10/91頁
文件大小： 907K
代理商： NQ80220
80220/80221
MD400159/E
18
3.8.3 Transmit Level Adjust
The transmit output current level is derived from an internal
reference voltage and the external resistor on REXT pin.
The transmit level can be adjusted with either (1) the
external resistor on the REXT pin, or (2) the four transmit
level adjust bits in the MI serial port Configuration 1 register
as shown in Table 3. The adjustment range is approxi-
mately -14% to +16% in 2% steps.
Table 3. Transmit Level Adjust
TLVL[3:0]
Gain
0000
1.16
0001
1.14
0010
1.12
0011
1.10
0100
1.08
0101
1.06
0110
1.04
0111
1.02
1000
1.00
1001
0.98
1010
0.96
1011
0.94
1100
0.92
1101
0.90
1110
0.88
1111
0.86
3.8.4 Transmit Rise And Fall Time Adjust
The transmit output rise and fall time can be adjusted with
either (1) the two pins TRFADJ[1:0], or (2) the two transmit
rise/fall time adjust bits in the MI serial port Configuration
1. The adjustment range is -0.25 nS to +0.5 nS in 0.25 nS
steps. When the TRFADJ[1:0] pins are set to 1 and 0,
respectively, the rise and fall times are set with the register
bits (with 0 ns as the default). When TRFADJ[1:0] pin are
set to anything other than 10, then the pins control the
transmit rise and fall time as shown in the Pin Description
and the TRFADJ[1:0] bits are disabled.
3.8.5 STP (150 Ohm) Cable Mode
The transmitter can be configured to drive 150 Ohm
shielded twisted pair cable.
The STP mode can be
selected by appropriately setting the cable type select bit
in the MI serial port Configuration 1 register. When STP
mode is enabled, the output current is automatically ad-
justed to comply with IEEE 802.3 levels.
3.8.6 Transmit Activity Indication
Transmit activity can be programmed to appear on some
of the PLED[5:0] pins by appropriately setting the pro-
grammable LED output select bits in the MI serial port LED
Configuration 2 register as described in Table 5. When
one or more of the PLED[5:0] pins is programmed to be an
activity or transmit activity detect output, that pin is as-
serted low for 100 mS every time a transmit packet occurs.
The PLED[5:0] output is open drain with pullup resistor
and can drive an LED from VCC or can drive another digital
input.
3.8.7 Transmit Disable
The TP transmitter can be disabled by setting the transmit
disable bit in the MI serial port Configuration 1 register.
When the transmit disable bit is set, the TP transmitter is
forced into the idle state, no data is transmitted, no link
pulses are transmitted, and internal loopback is disabled.
3.8.8 Transmit Powerdown
The TP transmitter can be powered down by setting the
transmit powerdown bit in the MI serial port Configuration
1 register. When the transmit powerdown bit is set, the TP
transmitter is powered down, the TP transmit outputs are
high impedance, and the rest of the 80220/80221 operates
normally.
3.9 TWISTED PAIR RECEIVER
3.9.1 Receiver - 100 Mbps
The TP receiver detects input signals from the twisted pair
input and convert it to a digital data bit stream ready for
clock and data recovery. The receiver can reliably detect
data from a 100Base-TX compliant transmitter that has
been passed through 0-100 meters of 100 Ohm category
5 UTP or 150 Ohm STP.
The 100 Mbps receiver consists of an adaptive equalizer,
baseline wander correction circuit, comparators, and MLT-
3 decoder. The TP inputs first go to an adaptive equalizer.
The adaptive equalizer compensates for the low pass
characteristic of the cable, and it has the ability to adapt
and compensate for 0-100 meters of category 5,100 Ohm
UTP or 150 Ohm STP twisted pair cable. The baseline
wander correction circuit restores the DC component of
the input waveform that was removed by external trans-
formers. The comparators convert the equalized signal
back to digital levels and are used to qualify the data with
the squelch circuit. The MLT-3 decoder takes the three
相關PDF資料
PDF描述
NRLM332M35VF Large Can Aluminum Electrolytic Capacitors
NRLM332M400V20X25F Large Can Aluminum Electrolytic Capacitors
NRLM332M400V20X30F Large Can Aluminum Electrolytic Capacitors
NRLM332M450VF Large Can Aluminum Electrolytic Capacitors
NRLM332M50V20X25F Large Can Aluminum Electrolytic Capacitors
相關代理商/技術參數
參數描述
NQ80225 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver
NQ8023A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MCC Manchester Code Converter
NQ80331M250 S L822 制造商:Intel 功能描述:I/O Processor FCBGA3
NQ80331M250 S L826 制造商:Intel 功能描述:I/O Processor FCBGA3 制造商:Intel 功能描述:LINDSAY, 32BIT PROCESSOR - Tape and Reel
NQ80331M250 S L82Q 制造商:Intel 功能描述:I/O Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*