- 您現在的位置：買賣IC網 > PDF目錄359738 > NJU26118 (New Japan Radio Co., Ltd.) NJU26100 Series Hardware Specification PDF資料下載
參數資料
| 型號： | NJU26118 |
| 廠商： | New Japan Radio Co., Ltd. |
| 英文描述： | NJU26100 Series Hardware Specification |
| 中文描述： | NJU26100系列硬件規格 |
| 文件頁數： | 13/17頁 |
| 文件大?。?/td> | 270K |
| 代理商： | NJU26118 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
Ver.2005-02-24
NJU26100 Series
- 13 -
5. Host Interface
The NJU26100 Series can be controlled via Serial Host Interface (SHI) using either of two serial bus formats:
4-Wire serial bus or I
2
C bus. Data transfers are in 8 bit packets (1 byte) when using either format. The SHI operates
only in a SLAVE fashion. A host controller connected to the interface always drives the clock (SCL / SCK) line and
initiates data transfers, regardless of the chosen communication protocol.
Table 5-1 Serial Host Interface Pin Description
Symbol
(I
2
C / Serial)
5
SCL/SCK
Serial Clock
Pin No.
4-Wire Serial bus Format
I
2
C bus Format
Serial Clock
Serial Data
(Bi-directional)
I
2
C bus address Bit1
I
2
C bus address Bit2
6
SDA/SDOUT
Serial Data Output
7
8
AD1/SDIN
AD2/SSb
Serial Data Input
SLAVE Select
Note : SDA /SDOUT pin is a bi-directional open drain.
SDA /SDOUT output is normal CMOS output in case of 4-Wire Serial bus mode and SSb=”Low”.
SDA /SDOUT output is Hi-Z state in case of 4-Wire Serial bus mode and SSb=”High”.
This pin requires a 4.7k pull-up resister in both 4-Wire serial and I
2
C bus mode.
5.1 4-Wire Serial Interface
The serial host interface can be configured for 4-Wire Serial bus communication by setting GPIO0 pin (*SEL1
pin)=”High” during the Reset initialization sequence. SHI bus communication is full-duplex; a write byte is shifted
into the SDIN pin at the same time that a read byte is shifted out of the SDOUT pin. Data transfers are MSB first
and are enabled by setting the Slave Select pin Low (SSb = 0). Data is clocked into SDIN on rising transitions of
SCK. Data is latched at SDOUT on falling transitions of SCK except for the first byte (MSB) which is latched on the
falling transitions of SSb. SDOUT is Hi-Z in case of SSb = “High”. SDOUT is CMOS output in case of SSb = “Low”.
SDOUT needs a pull-up resistor when SDOUT is Hi-Z.
*
It excepts NJU26150. Refer to each data sheet.
相關PDF資料 |
PDF描述 |
|---|---|
| NJU26119 | NJU26100 Series Hardware Specification |
| NJU26170 | NJU26100 Series Hardware Specification |
| NJU26171 | NJU26100 Series Hardware Specification |
| NJU26172 | NJU26100 Series Hardware Specification |
| NJU26173 | NJU26100 Series Hardware Specification |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NJU26119 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26120 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
| NJU26120VC2(TE1) | 制造商:New Japan Radio Co Ltd (NJR/JRC) 功能描述:Cut Tape 制造商:New Japan Radio 功能描述:0 |
| NJU26120VC2-TE1 | 制造商:New Japan Radio Co Ltd (NJR/JRC) 功能描述:Digital Signal Processor for TV SSOP24 |
| NJU26121 | 制造商:NJRC 制造商全稱:New Japan Radio 功能描述:NJU26100 Series Hardware Specification |
發布緊急采購，3分鐘左右您將得到回復。