- 您現在的位置：買賣IC網 > PDF目錄363259 > NIS5101E1T1 (ON SEMICONDUCTOR) SMART HotPlug IC/Inrush Limiter/Circuit Breaker PDF資料下載
參數資料
| 型號： | NIS5101E1T1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PSSO7 |
| 封裝： | SPAK-7 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 109K |
| 代理商： | NIS5101E1T1 |
NIS5101
http://onsemi.com
9
OPERATION DESCRIPTION
Turnon
The SMART HotPlug monitors the input voltage by
sensing the voltage across the Input + to Input pins. When
the UVLO voltage has been reached, the internal circuitry
slowly charges the gate of the internal SENSEFET
.
There will be a slight delay of several milliseconds before
the SENSEFET begins conduction. This may be increased
by adding a capacitor to the UVLO pin. For a discussion of
this, see application note AND8115/D.
The SENSEFET will increase the load current with a
controlled di/dt until the current limit level has been
reached. At this point the SENSEFET will enter a constant
current mode of operation until the load capacitor has been
fully charged. If the thermal limit threshold is reached
before the capacitor reaches its final charge level, the
device will shut down until the die temperature reaches
95
°
C and then restart, if it is the autoretry device. The
thermal latching version must not be allowed to reach the
thermal shutdown level at turnon as this will cause it to
latch in an off state.
During the capacitor charging period, the dv/dt of the
capacitor is:
dv dt
ILIMIT
CLOAD
Faults
Once the load capacitance is charged, the SENSEFET
will become fully enhanced as long as the current does not
reach the current limit threshold, or is shutdown due to an
overvoltage, undervoltage or thermal fault. Both the
UVLO and OVLO circuits incorporate hysteresis to assure
clean turnon and turnoffs with no chatter. The thermal
latching circuit will require the input power to be recycled
to resume operation after a fault. The current limit is always
active, so any transient or overload will always be limited.
Circuit Description
Undervoltage Lockout:
The UVLO circuit holds the chip
off when the input voltage is less than the turnon limit. It
includes internal hysteresis to assure clean on/off
switching. An internal divider sets the turnon voltage
level at 46 V. This voltage can be reduced by adding an
external resistor from the UVLO pin to the Input + pin. The
equivalent circuit is shown in Figure 17.
Figure 17. Undervoltage Lockout Circuit
Input +
UVLO/
ENABLE
Drain
R
UVLO
200 k
100 k
50 k
Input
V
z
12.5 V
ZD1
V
reg
相關PDF資料 |
PDF描述 |
|---|---|
| NIS5101E2T1 | SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| NIS5102QP1HT1 | High Side SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| NIS5102QP1HT1G | High Side SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| NIS5102QP2HT1 | High Side SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| NIS5102QP2HT1G | +12 V Telecom Power Conversion Solutions |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NIS5101E1T1G | 功能描述:熱插拔功率分布 -48V Hotswap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| NIS5101E2T1 | 功能描述:熱插拔功率分布 SMART HotSwap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| NIS5101E2T1G | 功能描述:熱插拔功率分布 -48V Hotswap RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| NIS5102 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Side SMART HotPlug IC/Inrush Limiter/Circuit Breaker |
| NIS5102QP1HT1 | 功能描述:熱插拔功率分布 MI HI SDE SMRT HOTPLUG RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。