- 您現(xiàn)在的位置：買賣IC網 > Datasheet目錄45 > NE1617ADS,112 (NXP Semiconductors)IC TEMP MONITOR 16SSOP Datasheet資料下載
參數資料
| 型號： | NE1617ADS,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 6/30頁 |
| 文件大小： | 305K |
| 描述： | IC TEMP MONITOR 16SSOP |
| 標準包裝： | 100 |
| 功能： | 溫度監(jiān)控系統(tǒng)（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -55°C ~ 125°C，外部傳感器 |
| 精確度： | ±3°C 本地（最大），±5°C 遠程（最大） |
| 拓撲： | ADC，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 管件 |
| 其它名稱： | 935268119112 NE1617ADS NE1617ADS-ND |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
NE1617A
All information provided in this document is subject to legal disclaimers.
?NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5 20 March 2012
6 of 30
NXP Semiconductors
NE1617A
Temperature monitor for microprocessor systems
Even though the NE1617A integrating A-to-D converter has a good noise performance,
using the average of 10 measurement cycles, high frequency noise filtering between D+
and D- should be considered. An external capacitor of 2200 pF typical (but not higher
than 3300 pF) connected between D+ and D- is recommended. Capacitance higher than
3300 pF will introduce measurement error due to the rise time of the switched current
source.
7.2 No calibration is required
As mentioned in Section 7.1
, the NE1617A uses two well-controlled current sources of
10 : 1 ratio to measure the forward voltage of the diode (V
BE
). This technique eliminates
the diode saturation current (a heavily process and temperature dependent variable), and
results in the forward voltage being proportional to absolute temperature.
7.3 Address logic
The address pins of the NE1617A can be forced into one of three levels: LOW (GND),
HIGH (V
DD
), or not connected (n.c.). Because the NE1617A samples and latches the
address pins at the starting of every conversion, it is suggested that those address pins
should be hard-wired to the logic applied, so that the logic is consistently existed at the
address pins. During the address sensing period, the device forces a current at each
address pin and compares the voltage developed across the external connection with the
predefined threshold voltage in order to define the logic level. If an external resistor is
used for the connection of the address, then its value should be less than 2 kW to prevent
the error in logic detection from happening. Resistors of 1 kW are recommended.
8. Temperature monitor with SMBus serial interface
8.1 Serial bus interface
The device can be connected to a standard 2-wire serial interface System Management
Bus (SMBus) as a slave device under the control of a master device, using two device
terminals SCLK and SDATA. The operation of the device to the bus is described with
details in the following sections.
8.2 Slave address
The device address is defined by the logical connections applied to the device pins ADD0
and ADD1. A list of selectable addresses are shown in Table 3
. The device address can
be set to any one of those nine combinations and more than one device can reside on the
same bus without address conflict. Note that the state of the device address pins is
sampled and latched not only at power-up step, but also at starting point of every
conversion.
Table 3.
Device slave address
n.c. = not connected
ADD0
[1]
ADD1
[1]
Address byte
GND
GND
0011 000
GND
n.c.
0011 001
GND
V
DD
0011 010
n.c.
GND
0101 001
相關PDF資料 |
PDF描述 |
|---|---|
| NE1619DS,118 | IC TEMP MONITOR 16SSOP |
| NIS5112D1R2G | IC ELECTRONIC FUSE HOTSWAP 8SOIC |
| NIS5132MN2TXG | IC ELECTRONIC FUSE 12V 10DFN |
| NIS5132MN3TXG | IC ELECTRONIC FUSE 12V 10-DFN |
| NSI45015WT1G | IC LED DRIVER LINEAR SOD-123 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NE1617DS | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND REM +/- 3OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NE1617DS,112 | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NE1617DS,118 | 功能描述:板上安裝溫度傳感器 I2C LOC +/- 2OC AND REM +/- 3OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NE1618 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Temperature monitor for microprocessor systems |
| NE1618DS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Temperature monitor for microprocessor systems |
發(fā)布緊急采購，3分鐘左右您將得到回復。