- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP5005 (ON SEMICONDUCTOR) Compact Backlight LED Boost Driver(背光LED升壓驅動器) PDF資料下載
參數資料
| 型號： | NCP5005 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Compact Backlight LED Boost Driver(背光LED升壓驅動器) |
| 中文描述： | 緊湊型背光LED升壓驅動器（背光的LED升壓驅動器） |
| 文件頁數： | 3/23頁 |
| 文件大?。?/td> | 239K |
| 代理商： | NCP5005 |
NCP5005
http://onsemi.com
3
PIN FUNCTION DESCRIPTION
Pin
Pin Name
Type
Description
1
V
out
POWER
This pin is the power side of the external inductor and must be connected to the
external Schottky diode. It provides the output current to the load. Since the boost
converter operates in a current loop mode, the output voltage can range up to
+24 V but shall not extend this limit. However, if the voltage on this pin is higher
than the Over Voltage Protection threshold (OVP) the device comes back to
shutdown mode. To restart the chip, one must either send a Low to High
sequence on Pin EN, or switch off the V
bat
supply. A capacitor must be used on
the output voltage to avoid false triggering of the OVP circuit. This capacitor
should be 1.0 F minimum. Ceramic type, (ESR <100 m ), is mandatory to
achieve the high end efficiency. This capacitor limits the noise created by the fast
transients present in this circuitry. In order to limit the inrush current and to
operate with an acceptable startup time, it is recommended to use any value
between 1.0 F and 8.2 F capacitor maximum. Care must be observed to avoid
EMI through the PCB copper tracks connected to this pin.
2
GND
POWER
This pin is the system ground for the NCP5005 and carries both the power and
the analog signals. High quality ground must be provided to avoid spikes and/or
uncontrolled operation. Care must be observed to avoid highdensity current flow
in a limited PCB copper track. Ground plane technique is recommended.
3
FB
ANALOG INPUT
This pin provides the output current range adjustment by means of a sense
resistor connected to the analog control or with a PWM control. The dimming
function can be achieved by applying a PWM voltage technique to this pin (see
Figure 29). The current output tolerance depends upon the accuracy of this
resistor. Using a
5% metal film resistor or better, yields a good enough output
current accuracy.
Note: A builtin comparator switch OFF the DC/DC converter if the voltage
sensed across this pin and ground is higher than 700 mV (typical).
4
EN
DIGITAL INPUT
This is an ActiveHigh logic input which enables the boost converter. The builtin
pull down resistor disables the device when the EN pin is left open. The LED
brightness can be controlled by applying a pulse width modulated signal to the
enable pin (see Figure 31).
5
V
bat
POWER
The external voltage supply is connected to this pin. A high quality reservoir
capacitor must be connected across Pin 1 and Ground to achieve the specified
output voltage parameters. A 4.7 F/6.3 V, low ESR capacitor must be connected
as close as possible across Pin 5 and ground Pin 2. The X5R or X7R ceramic
MURATA types are recommended. The return side of the external inductor shall
be connected to this pin. Typical application will use a 22 H, size 1008, to handle
the 1.0 to 100 mA max output current range. On the other hand, when the desired
output current is above 20 mA, the inductor shall have an ESR < 1.5 to achieve
a good efficiency over the V
bat
range
.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP500SN185T1G | 150 mA CMOS Low Noise Low−Dropout Voltage Regulator |
| NCP500SN18T1G | 150 mA CMOS Low Noise Low−Dropout Voltage Regulator |
| NCP500SN26T1G | 150 mA CMOS Low Noise Low−Dropout Voltage Regulator |
| NCP500SN27T1G | 150 mA CMOS Low Noise Low−Dropout Voltage Regulator |
| NCP500SN30T1G | 150 mA CMOS Low Noise Low−Dropout Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP5005GEVB | 功能描述:電源管理IC開發工具 NCP5005 EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP5005SNT1G | 功能描述:LED照明驅動器 ANA WHITE LED DRIVER RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| NCP5006 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators |
| NCP5006_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Compact Backlight LED Boost Driver |
| NCP5006EVB | 功能描述:LED 照明開發工具 ANA WHITE LED DRIVER EVB RoHS:否 制造商:Fairchild Semiconductor 產品:Evaluation Kits 用于:FL7732 核心: 電源電壓:120V 系列: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。