- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP4331 (ON SEMICONDUCTOR) Synchronous Buck Controller for High Efficiency Post Regulation PDF資料下載
參數資料
| 型號： | NCP4331 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Synchronous Buck Controller for High Efficiency Post Regulation |
| 中文描述： | 同步降壓控制器的高效率后調整 |
| 文件頁數： | 4/23頁 |
| 文件大小： | 195K |
| 代理商： | NCP4331 |
NCP4331
http://onsemi.com
4
DETAILED PIN DESCRIPTIONS
Pin Number
Name
Function
1
CSout
Pin 1 is the output of the auxiliary error amplifier embedded in the NCP4331. This allows for the prevention
of excessive coil or load current. Pin 1 can clamp the main error amplifier output. Controlling the coil
current by this auxiliary error amplifier can provide a CCCV characteristic.
2
CSin-
Inverting input of the auxiliary error amplifier that is generally used to control the coil current.
3
CSin+
Noninverting input of the auxiliary error amplifier that is generally used to control the coil current.
4
UVP/
STDWN
This pin is designed to detect too low input voltage pulses and to turn off both the low-side and high-side
drivers in such a faulty condition. Also, the soft-start pin is grounded so that the circuit smoothly recovers
operation when the detected fault disappears. This UVP detection function features some programmable
hysteresis to avoid erratic turns on and off of the device. Ground Pin 4 to shutdown the part.
5
COMP
This pin makes available the output of the internal error amplifier, for appropriate compensation of the
regulation loop.
6
FB
Pin 6 is the feed-back pin that must receive a portion of the output voltage to regulate. It is connected to
the inverting input of the internal error amplifier. The regulation reference is better
125
°
C temperature range.
2% over the -40
°
C to
7
Soft-Start/
Dmax
Apply a capacitor to Pin 7 to slow down the start-up phase and reduce the stress during this sequence.
Place a resistor between Pin 7 and ground to adjust the maximum duty-cycle of the high-side MOSFET.
Combine the two functions by implementing these two components in parallel.
8
Cramp
This pin sources a constant current. Connect a capacitor to create a voltage ramp. This ramp is summed
to the error amplifier output and compared to a constant voltage reference (V
PWM
) to adjust the
post-regulator duty-cycle.
9
SYNC
This pin is designed to receive a portion of the input voltage, to synchronize the post-regulator activity to
its pulsed input voltage. Also, the high-side drive cannot be high state if the “SYNC” pin voltage is low.
10
GND
Ground pin of the circuit.
11
LS_DRV
”LS_DRV“ is the driver output of the low-side MOSFET gate.
12
VDD
“VDD” is the circuit power source that is typically provided by the VCC Pin. A 0.1 F to 1 F ceramic
capacitor should be connected between this pin and ground for decoupling.
13
HB
Connect the common node of the two MOSFETs to this pin.
14
HS_DRV
“HS_DRV” is the driver output of the high-side MOSFET gate.
15
BST
“BST” is the bootstrap pin. A 0.1 F to 1 F ceramic capacitor should be connected between this pin and
the “HB” node. The “BST” voltage feeds the high-side driver (“HS_DRV”).
16
VCC
A DC voltage (up to 30 V) must be applied to this pin. This voltage is internally post-regulated down to
7.5 V to provide the V
DD
voltage that powers the circuit.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP4420 | 6A High-Speed MOSFET Drivers |
| NCP4429 | 6A High-Speed MOSFET Drivers |
| NCP4423 | 3A Dual High-Speed MOSFET Drivers |
| NCP4894FCT1 | 1.8 Watt Differential Audio Power Amplifier with Selectable Shutdown |
| NCP4896FCT1G | 1.0 Watt Audio Power Amplifier with Earpiece Driving Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP4331DBR2G | 功能描述:IC REG CTRLR BUCK PWM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| NCP4331DR2G | 功能描述:功率驅動器IC PWM CONTROLLER RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| NCP433FCT2G | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5A Ultra-Small Controlled Load Switch with Auto-Discharge Path |
| NCP434 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:2A Ultra-Small Controlled Load Switch with |
| NCP434FCT2G | 制造商:ON Semiconductor 功能描述:2A LOAD SWITCH WITH DISCH - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / 2A LOAD SWITCH WITH DISCH |
發布緊急采購，3分鐘左右您將得到回復。