參數資料
型號: MX812DW
廠商: Electronic Theatre Controls, Inc.
元件分類: Codec
英文描述: VSR CODEC WITH DRAM CONTROL
中文描述: 振動時效編解碼器DRAM的控制
文件頁數: 3/13頁
文件大小: 115K
代理商: MX812DW
VSR CODEC with DRAM CONTROL
3
MX812 PRELIMINARY INFORMATION
1997 MX
COM Inc.
4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA
www.mxcom.com Tele: 800 638-5577 910 744-5050 Fax: 910 744-5054
Doc. # 20480076.003
All trademarks and service marks are held by their respective companies.
11
Audio Out:
The analog output to the Audio Processor “Play” input when the VSR Codec is
configured as a Decoder. When configured as an active Decoder but with no Play Page commands
(62
) active, the VSR Codec will play-out an idle pattern of “101010........10
s
”. When not configured as
a Decoder, or Powersaved (Mode Register), this output will be held at V
via an internal 500k
resistor. The output at this pin is unfiltered; an external speechband filter – such as that included on
the MX816/826/836 Audio Processors – will be required. Since this output is centered around V
DD
/2 a
coupling capacitor is required.
12
E
:
The Encoder d.c. internal balancing circuitry line. This pin should be decoupled to V
by
capacitor C
(see Figure 2).
Note
that in the ‘Encode’ mode (Mode Register DE and PS both “0”) the
Codec drives this pin to approximately V
/2 through a very high impedance; it can take more than
one second for the E
voltage to stabilize when power is first applied to this device. A faster start-up
can be achieved by setting Bit DE or PS to “1” for 250mS (approx) during power-up. This will cause
the E
BIAS
pin to be connected to V
BIAS
through a resistance of approximately 100k
.
13
Audio In:
The analog input to the VSR Codec in the Encode mode. When not configured as an
Encoder, or Powersaved (Mode Register), this input will be held at V
via an internal 500k
resistor.
This pin should be coupled via a capacitor, see Figure 2. As this input does not contain an internal
audio filter, the audio to this pin should be limited to a 3400Hz “speechband” by an external audio filter
– such as included in the MX816/826/836 Audio Processors.
14
V
SS
:
The “analog” ground connection. See D
GND
description.
15
A0:
16
A1:
17
A2:
18
A3:
19
A4:
20
A5:
21
A6:
22
A7:
23
A8:
24
A9:
25
A10/R2:
A dual function output pin selected by the memory size (MS) bit (Mode Register),
as detailed in the table below:
MS bit
“0”
“1”
DRAMs
1Mbits'
4Mbit
Connected To
DRAM No 2 RAS
DRAM A10
This Output
RAS2
A10 Signal
26
RAS:
An output from the VSR Codec which should be connected to the “Row Address Strobe” pin of
the 4Mbit DRAM or the first 1Mbit DRAM, see Figure 4, Example DRAM connections.
27
D
:
The digital signal ground connection to the VSR Codec. Both D
and V
pins should be
connected to the negative side of the d.c. power supply. However, a printed circuit board should be
laid out so that D
GND
is connected as closely as possible to the DRAM section ground pins.
28
V
:
Positive supply rail. A single, stable +5-volt supply is required. Levels and voltages within the
VSR Codec are dependent upon this supply. This pin should be decoupled to V
SS
via capacitor C
5
,
located close to the MX812 pins.
Pin
Function
DRAM address line outputs from the MX812.
These pins should be connected to the corresponding address
inputs of the associated DRAM.
相關PDF資料
PDF描述
MX812J VSR CODEC WITH DRAM CONTROL
MX841 White LED Step-Up Converter
MX88L284AEC Highly integration chip for Flat Panel Display application
MXA2500U Ultra Low Noise, 1g Dual Axis Accelerometer with Analog Outputs
MXA28A MOLDED TSSOP JEDEC
相關代理商/技術參數
參數描述
MX812J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:VSR CODEC WITH DRAM CONTROL
MX-818 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HIGH SPEED CMOS PROGRAMMABLE ANALOG MULTIPLEXERS
MX-818C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HIGH SPEED CMOS PROGRAMMABLE ANALOG MULTIPLEXERS
MX821 制造商:Applied Research Technology 功能描述:Rack Mount Eight Channel Mixer with Equalizer 制造商:APPLIED RESEARCH TECHNOLOGY 功能描述:MIXER EIGHT CHANNEL WITH EQ AND DIRECT OUTS
MX8217PC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC