參數資料
型號: MT9125
廠商: Mitel Networks Corporation
英文描述: Dual ADPCM Transcoder(雙ADPCM編解碼器)
中文描述: 雙差分PcM轉碼器(雙差分PcM編解碼器)
文件頁數: 6/20頁
文件大?。?/td> 172K
代理商: MT9125
MT9125
Preliminary Information
8-78
Figure 4 - ST-BUS Mode Relative Timing
F0i
DSTi/o
EN1
EN2
ADPCMi/o
EN1
EN2
ADPCMi/o
Channel 0
Channel 1
Channel 2
Channel 3
B1
B2
B1
B2
B1
B2
B1
B2
ENS=0
ENS=1
In ST-BUS mode the ENA, ENB1 and ENB2 input strobes are ignored. All timing is
dervied internally from the F0i, MCLK and ENS inputs.
the device and must, therefore, be present whenever
a transcoding operation is required. These inputs
may be tied together and connected to the same
strobe for single channel operation. Only the B1
nibble is valid in this mode. Data is latched into the
DSTi pin with the falling edge of the bit clock while
output data is made available at DSTo on the rising
edge of the bit clock.
ST-BUS Conversion (F0i, C2o, EN1, EN2, ENS)
A simple converter circuit is incorporated which
allows ST-BUS signals to be converted to SSI
signals. In this manner it is very simple for an ST-
BUS application to be mixed with CODECs utilizing a
strobed data I/O.
This converter circuit consists of the F0i input and
C2o, EN1 and EN2 output pins (as well as the MCLK
input master clock). The output C4b clock and frame
pulse strobe (F0b), from the ST-BUS layer 1
transceiver, are connected directly to the master
clock (MCLK) and frame pulse (F0i) inputs of the
transcoder. A 2.048 MHz (C2o) bit clock output is
made available when a valid Frame Pulse is
connected to the F0i pin or the F0i pin is tied high. If
the F0i pin is tied low the C2o output is forced
continuously to a logic low level (not tri-stated).
Forcing the C2o output to logic low enhances power
conservation as well as removing a non-required
clock signal from the circuit. This 2.048 MHz bit clock
may be used to control external CODEC functions.
The 4.096 MHz and frame pulse signals are also
decoded into two output strobes corresponding to
the B1 and B2 channel timeslots of the ST-BUS.
These strobes (EN1 and EN2) are then used to
control the timing inputs of an external CODEC. A
typical example of this connection scheme is shown
in the application diagram of Figure 7.
The Enable Strobe pin (ENS) is used to position the
output strobes EN1 and EN2 within the ST-BUS
frame. Referring to Figure 4, when ENS=0 the output
strobes are positioned in channels 0 and 1 of the ST-
BUS frame. When ENS=1 the output strobes are
positioned in channels 2 and 3 of the ST-BUS frame.
This flexibility allows the transcoder to be used in ST-
BUS basic rate applications where channels 0 and 1
are defined as the D and C channels, respectively,
and also in line-card applications where the full
2.048 MHz bandwidth is used for conveying data
and/or digitally encoded voice information.
相關PDF資料
PDF描述
MT91600 Programmable SLIC(可編程用戶線路接口電路(在轉換系統和用戶環間提供一個接口))
MT9162 5 Volt Single Rail Codec(5V 單軌編解碼器)
MT9174 ISO2-CMOS ST-BUS⑩ FAMILY Digital Network Interface Circuit with Receive Sync Marker Bit
MT9174AE ISO2-CMOS ST-BUS⑩ FAMILY Digital Network Interface Circuit with Receive Sync Marker Bit
MT9174AN ISO2-CMOS ST-BUS⑩ FAMILY Digital Network Interface Circuit with Receive Sync Marker Bit
相關代理商/技術參數
參數描述
MT9125AE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Dual ADPCM Transcoder
MT9125AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Dual ADPCM Transcoder
MT9126 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Quad ADPCM Transcoder
MT9126AE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS Quad ADPCM Transcoder
MT9126AE1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28PDIP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP