參數資料
型號： MT9079
廠商： Mitel Networks Corporation
英文描述： Advanced Controller for E1(先進的E1幀調節器和控制器)
中文描述： 高級控制器素E1（先進的素E1幀調節器和控制器）
文件頁數： 8/60頁
文件大小： 347K
代理商： MT9079
MT9079
4-214
G.704 and G.732 for more details on CAS
mutliframing requirements.
A CAS signalling multiframe consists of 16 basic
frames (numbered 0 to 15), which results in a
multiframe repetition rate of 2 msec. It should be
noted that the boundaries of the signalling
multiframe may be completely distinct from those of
the CRC-4 multiframe. CAS multiframe alignment is
based on a multiframe alignment signal (a 0000 bit
sequence), which occurs in the most significant
nibble of time slot 16 of basic frame zero of the CAS
multiframe. Bit 6 of this time slot is the multiframe
alarm bit (usually designated Y). When CAS
multiframing is acquired on the receive side, the
transmit Y-bit is zero; when CAS multiframing is not
acquired, the transmit Y-bit is one. Bits 5, 7 and 8
(usually designated X) are spare bits and are
normally set to one if not used.
Time slot 16 of the remaining 15 basic frames of the
CAS multiframe (i.e., basic frames 1 to 15) are
reserved for the ABCD signalling bits for the 30
payload channels. The most significant nibbles are
the reserved for channels 1 to 15 and the least
significant nibbles are reserved for channels 16 to
30. That is, time slot 16 of basic frame 1 has ABCD
for channel 1 and 16, time slot 16 of basic frame 2
has ABCD for channel 2 and 17, through to time slot
16 of basic frame 15 has ABCD for channel 15 and
30.
MT9079 Access and Control
The Control Port Interface
The control and status of the MT9079 is achieved
through one of three generic interfaces, which are
parallel microprocessor, serial microcontroller, and
ST-BUS. This control port selection is done through
pins S/P and ST/SC.
The parallel microprocessor port (S/P = 0 and ST/SC
= AC4) is non-multiplexed and consists of an eight bit
bidirectional
data
bus
address/command bus (AC0-AC4), read/write (R/W),
chip select (CS), data strobe (DS) and an interrupt
request (IRQ). This port can be easily interfaced to
most high speed parallel microprocessors.
(D0-D7),
a
five
bit
The serial microcontroller port (S/P = 1 and ST/SC =
0) consists of a receive data input (RxD), serial clock
input (SCLK), serial data input/output (SIO), interrupt
request (IRQ), and chip select (CS). This port will
automatically interface to Intel, Motorola or National
microcontrollers
in
either
asynchronous modes. When controller mode is
synchronous
or
selected, the SCLK input is sampled when CS is
brought low. If SCLK is high the device is in Intel
mode; if SCLK is low it will be in Motorola/National
Microwire mode.
The ST-BUS port (S/P = 1 and ST/SC = 1) consists
of control streams CSTi0 and CSTi1 and status
stream CSTo0. It should be noted that in this mode
access to the circular buffers and notional bit buffers
is not provided, and the IRQ function is not
supported. This port meets the requirements of the
"ST-BUS Generic Device Specification", Mitel
Application Note MSAN-126.
Figure 3 - Control Port Interface
Control and Status Register Access
The
microcontroller interfaces gain access to specific
registers of the MT9079 through a two step process.
First, writing to the Command/Address Register
(CAR) selects one of the 14 pages of control and
status registers (CAR address: AC4 = 0, AC3-AC0 =
parallel
microprocessor
and
serial
IRQ
D0
CONTROL
INTERFACE
PARALLEL
μ
P
D7
AC4
AC0
R/W
CS
DS
S/P
CSTi2
CSTo1
IRQ
RxD
CONTROL
INTERFACE
SERIAL
μ
P
ST/SC
SIO
CS
SCLK
S/P
CSTi2
CSTo1
CONTROL
INTERFACE
CSTo0
ST/SC
CSTi0
CSTi1
S/P
CSTi2
CSTo1
ST-BUS
+5V
+5V
+5V
相關PDF資料
PDF描述
MT9080B SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊)
MT90810 Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路)
MT90812 Integrated Digital Switch (IDX)(集成數字開關)
MT90840AK Distributed Hyperchannel Switch
MT90840AP Distributed Hyperchannel Switch
相關代理商/技術參數
參數描述
MT9079AC 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS? FAMILY Advanced Controller for E1
MT9079AE 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS? FAMILY Advanced Controller for E1
MT9079AL 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Advanced Controller for E1
MT9079AP 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Advanced Controller for E1
MT9079APR 制造商:Microsemi Corporation 功能描述:FRAMER E1 5V 44PLCC - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*