- 您現在的位置：買賣IC網 > PDF目錄359234 > MT9043 (Zarlink Semiconductor Inc.) T1/E1 System Synchronizer PDF資料下載
參數資料
| 型號： | MT9043 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | T1/E1 System Synchronizer |
| 中文描述： | T1/E1的系統同步 |
| 文件頁數： | 5/29頁 |
| 文件大小： | 453K |
| 代理商： | MT9043 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MT9043
Data Sheet
5
Zarlink Semiconductor Inc.
Time Interval Error (TIE) Corrector Circuit
The TIE corrector circuit, when enabled, prevents a step change in phase on the input reference signals (PRI or
SEC) from causing a step change in phase at the input of the DPLL block of Figure 1.
During reference input rearrangement, such as during a switch from the primary reference (PRI) to the secondary
reference (SEC), a step change in phase on the input signals will occur. A phase step at the input of the DPLL
would lead to unacceptable phase changes in the output signal.
As shown in Figure 3, the TIE Corrector Circuit receives one of the two reference (PRI or SEC) signals, passes the
signal through a programmable delay line, and uses this delayed signal as an internal virtual reference, which is
input to the DPLL. Therefore, the virtual reference is a delayed version of the selected reference.
Figure 3 - TIE Corrector Circuit
During a switch from one reference to the other, the State Machine first changes the mode of the device
from Normal to Freerun. The Compare Circuit then measures the phase delay between the current phase
(feedback signal) and the phase of the new reference signal. This delay value is passed to the Programmable
Delay Circuit (See Figure 3). The state machine then returns the device to Normal Mode and the DPLL begins
using the new virtual reference signal. The difference between the phase position of the new virtual reference and
the previous reference is less than 1
μ
s.
Since internal delay circuitry maintains the alignment between the old virtual reference and the new virtual
reference, a phase error may exist between the selected input reference signal and the output signal of the DPLL.
This phase error is a function of the difference in phase between the two input reference signals during reference
FS2
FS1
Input Frequency
0
0
19.44MHz
0
1
8kHz
1
0
1.544MHz
1
1
2.048MHz
Table 1 - Input Frequency Selection
Programmable
Delay Circuit
Control Signal
Delay Value
TCLR
Resets Delay
Compare
Circuit
TIE Corrector
Enable
from
State Machine
Control
Circuit
Feedback
Signal from
Frequency
Select MUX
PRI or SEC
from
Reference
Select Mux
Virtual
Reference
to DPLL
相關PDF資料 |
PDF描述 |
|---|---|
| MT9043AN | T1/E1 System Synchronizer |
| MT9043AN48PINSSOP | T1/E1 System Synchronizer |
| MT9045 | T1/E1/OC3 System Synchronizer |
| MT9045AN | T1/E1/OC3 System Synchronizer |
| MT9046 | T1/E1 System Synchronizer with Holdover |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9043AN | 制造商:Microsemi Corporation 功能描述: |
| MT9043AN1 | 制造商:Microsemi Corporation 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER 制造商:Microsemi Corporation 功能描述:FRAMER E1/T1 3.3V 48SSOP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP |
| MT9043AN48PINSSOP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 System Synchronizer |
| MT9043ANR1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1 /T1 3.3V 48SSOP - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP |
| MT9044 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/OC3 System Synchronizer |
發布緊急采購，3分鐘左右您將得到回復。