- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8920B (Mitel Networks Corporation) ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）) PDF資料下載
參數資料
| 型號： | MT8920B |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）) |
| 中文描述： | 意法半導體總線并行訪問電路（串行通信總線（圣總線）并行存取電路（在圣總線和并行系統間提供一個簡單接口）） |
| 文件頁數： | 8/29頁 |
| 文件大?。?/td> | 215K |
| 代理商： | MT8920B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MT8920B
CMOS
3-10
Timing information for data transfers on this interface
is shown in Figure 14. The Mode 1 interface is
designed to operate directly with a 68000-type
asynchronous bus but can easily accommodate most
other popular microprocessors as well.
Control Registers
Two control registers allow control of Mode 1
features. Control Register 1 provides bits to select
the type of interrupt, to enable interrupts from two
different and independent sources and to reset the
interrupt registers. Also contained in Control
Register 1 are bits to configure the device for 24 or
32 channel operation and to expand the address
range for convenient access to the second transmit
RAM Tx1. A description of the bit functions in
Control Register 1 is shown in Table 3.
Mode 1 provides various loopback paths and output
configuration options which are controlled by bits in
Control Register 2. Bits D
0
, D
1
of Control Register 2
configure loopbacks using input and output streams
STi0, STo0 as described in Table 4. The input
stream STi0 can be looped back to source the output
stream STo0 as well as receive RAM Rx0. The
transmit RAM Tx0 can be looped to source the
receive RAM Rx0, as well as STo0 and, the transmit
RAM Tx0 can be looped to the receive RAM Rx0
while STi0 sources STo0. The function of these
loopback configurations is shown in Figure 5.
In a similar way, the output STo1 can be reconfigured
for different functionality. Bits D
2
and D
3
of Control
Register 2 allow STo1 to be sourced, with a one
frame delay via Tx1 from receive stream STi0. STo1
can also output the result of a comparison of the
contents of Tx1 ram with input stream STi0. These
output configurations of STo1 are shown in Figure 6
a and b. Figure 6 c shows the effect of combining
these two features.
Interrupt Registers
Interrupts can be generated in Mode 1 only. Two
channels of the ST-BUS input stream, STi0, can be
selected to provide an interrupt to the system.
Interrupts can be of two types: Static or Dynamic.
Static interrupts are caused when data within a
selected channel matches a given pattern. Dynamic
interrupts occur when bits in a selected channel
change state (1 to 0, 0 to 1 or toggle). Interrupts are
controlled through two identical paths (1 and 2)
consisting of the following registers:
Interrupt Channel Address (1/2):
The address
(0-31) of the channel which will generate the
interrupt is stored in this register.
Image Register (1/2):
The contents of the
channel causing the interrupt is stored in this
register. Reading this register will clear its contents.
Match Byte Register (1/2):
In static mode this
register is used to store the byte which will be
compared with the contents of the selected channel
causing the interrupt.
In dynamic mode, the bits in this register and the
corresponding bit in the Interrupt Mask Register
define the type of dynamic interrupt (i.e., 0 to 1, 1 to
0, toggle). (Refer to Table 5.)
Table 4. Control Register 2 Bit Definitions
Bit
Name
Description
7-4
3-2
(Unused)
CONFIG
STo1 Output Configuration Bits:
D
3
D
2
= 00-
Normal operation. ST-BUS stream from Tx1 is output on STo1 pin.
01-
STi0 stream is output on STo1 pin delayed one frame (Figure 6 a).
10-
STi0 is compared through XOR (exclusive OR) with ST-BUS stream
from Tx1 and output at STo1 (Figure 6 b).
11-
STi0 stream, delayed one frame (via Tx1), is compared (XOR) with the
next frame arriving at STi0 and the result output at STo1 (Figure 6 c).
Internal Loopback Configuration Bits:
D
1
D
0
= 00-
Normal operation. No internal loops.
01-
Loop STi0 to STo0 while still receiving STi0 in Rx0 (Figure 5 a).
10-
Loop Tx0 output ST-BUS stream to Rx0 input ST-BUS stream while
outputting Tx0 output to STo0. STi0 is not received (Figure 5 b).
11-
Loop Tx0 output ST-BUS stream to Rx0 input ST-BUS stream. Loop
STi0 to STo0 (Figure 5 c).
1-0
LOOPBACK
相關PDF資料 |
PDF描述 |
|---|---|
| MT8924-1 | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924AE | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924AS | PCM Conference Circuit (PCC) Preliminary Information |
| MT8924 | PCM Conference Circuit (PCC) Preliminary Information |
| MT8930B | () |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8920B-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit |
| MT8920BC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit |
| MT8920BE | 制造商:Mitel Networks Corporation 功能描述:COMMUNICATIONS INTERFACE, 28 Pin, Plastic, DIP |
| MT8920BE1 | 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PDIP - Rail/Tube 制造商:Microsemi 功能描述:Microsemi MT8920BE1 Interface Misc |
| MT8920BP | 制造商:Microsemi Corporation 功能描述: 制造商:MITEL 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。