參數資料
型號： MT8920B
廠商： Mitel Networks Corporation
英文描述： ST-BUS Parallel Access Circuit(串行通信總線（ST-Bus）并行存取電路（在ST總線和并行系統間提供一個簡單接口）)
中文描述： 意法半導體總線并行訪問電路（串行通信總線（圣總線）并行存取電路（在圣總線和并行系統間提供一個簡單接口））
文件頁數： 5/29頁
文件大小： 215K
代理商： MT8920B
CMOS
MT8920B
3-7
24/32 Channel Operation
The STPA may be configured to operate as a 32
channel or 24 channel device. This feature, which is
available in all three modes of operation, is
particularly useful in applications involving data
access to CEPT and T1 digital trunk interfaces.
When used as a data interface to Mitel‘s CEPT
digital trunks, the STPA maps the 32 consecutive
bytes of each dual port memory directly to ST-BUS
channels 0-31. This is performed by the address
generator shown in the functional block diagram (see
Figure 1). Figures 4 c & d show the relationship
between relative dual port RAM locations and
corresponding ST-BUS channels, for both input and
output serial streams, when the STPA is configured
as a 32 channel device.
When used as a data interface to Mitel’s T1 trunk
devices, however, only the first 24 consecutive RAM
locations are mapped to 24 of the 32 ST-BUS
channels. This mapping follows a specific pattern
which corresponds with the data streams used by
Mitel‘s T1 products. Instead of a direct correlation
(as in 32 channel operation), the 24 consecutive
RAM locations are mapped to the ST-BUS with every
fourth channel, beginning at channel 0, set to FF
16
(ie. channel 0, 4, 8, 12, 16, 20, 24 and 28). Figures
4 a & b show the relationship between RAM
locations and ST-BUS channel configuration. This
feature allows the STPA to be interfaced directly to
Mitel’s T1 trunk family.
When the STPA is operated in Mode 1, 24 and 32
channel configurations are selected using bit D
5
(RAMCON) in Control Register 1. D
5
= 0 selects 32
channel operation and D
5
= 1 selects 24 channel
operation. When the STPA is operated in Modes 2 or
3, however, the channel configuration is done
using input
24/32 (pin 25). When 24/32 = 1 the
device uses all 32 channels and when 24/32 = 0 it
uses 24.
Dual Port RAMS
Each of the three serial ST-BUS streams is
interfaced to the parallel bus through a 32 byte dual
port RAM. This allows parallel bus accesses to be
performed asynchronously while accesses at the
ST-BUS port are synchronous with ST-BUS clock.
As with any dual port RAM interface between two
asynchronous systems, the possibility of access
contention
exists.
The
occurrence by recognizing contention only when
accesses are performed at the same time for the
same 8-bit cell within the dual port RAM’s.
Furthermore, the probability of contention is
STPA
minimizes
this
lessened since ST-BUS accesses require only the
last half cycle of C4i of every channel. When
contention does occur, priority is always given to the
ST-BUS access.
The STPA indicates this contention situation in a
different manner for Modes 1 and 2. In Mode 1, the
contention
is
masked
"handshaking" method used to transfer data on
this 68000-type interface. Data Strobe (DS)
and Data Transfer Acknowledge (DTACK) control
the exchange. If contention should occur the
device will delay returning DTACK and thus stretch
the bus cycle until the
μ
P access can be completed.
by
virtue
of
the
In Mode 2, if access is attempted during a
"contention window" the STPA will supply the
BUSY signal to delay the start of the bus cycle. This
“contention window” is defined as shown in Figure
16. The window exists during the last cycle of C4i
clock in each channel timeslot. Although ST-BUS
access is only required during the last half of this
clock period, the “contention window“ exists for the
entire clock period since a parallel access occurring
just prior to an ST-BUS access will not complete
before the ST-BUS access begins. Figure 16 further
shows four possible situations that may occur when
parallel accesses are attempted in and around the
“contention window”. Condition 1 indicates that an
access occurring prior to the contention window but
lasting into the first half of it will complete normally
with no contention arbitration. If the access should
extend past the first half of the contention window
and into the ST-BUS access period, the BUSY signal
will be generated. Conditions 3 and 4 show accesses
occurring inside the contention window. These
accesses will result in BUSY becoming active
immediately after the access is initiated and
remaining active as shown in Figure 16.
Access contention is non-existent in Mode 3 since
the parallel bus signals, driven by the STPA, are
synchronized to the ST-BUS clocks.
Mode 1 -
μ
P Peripheral Mode
In Mode 1, the STPA operates as an asynchronous
68000-type microprocessor peripheral. All three
dual-port RAMS (Tx0, Tx1, Rx0) are made available
and may be configured as 32 or 24 byte RAM’s. Also
available are the full complement of control and
interrupt registers. The address map for Mode 1 is
shown in Table 2.
The STPA, in Mode 1, uses signals CS, R/W,
(Data Strobe), DTACK (Data Acknowledge) IRQ, and
IACK (Interrupt Acknowledge) at the parallel interface.
The pinout of the device is shown in Figure 3.
DS
相關PDF資料
PDF描述
MT8924-1 PCM Conference Circuit (PCC) Preliminary Information
MT8924AE PCM Conference Circuit (PCC) Preliminary Information
MT8924AS PCM Conference Circuit (PCC) Preliminary Information
MT8924 PCM Conference Circuit (PCC) Preliminary Information
MT8930B ()
相關代理商/技術參數
參數描述
MT8920B-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit
MT8920BC 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY ST-BUS Parallel Access Circuit
MT8920BE 制造商:Mitel Networks Corporation 功能描述:COMMUNICATIONS INTERFACE, 28 Pin, Plastic, DIP
MT8920BE1 制造商:Zarlink Semiconductor Inc 功能描述:ST-BUS PARALLEL ACCESS CIRCUIT 28PDIP - Rail/Tube 制造商:Microsemi 功能描述:Microsemi MT8920BE1 Interface Misc
MT8920BP 制造商:Microsemi Corporation 功能描述: 制造商:MITEL 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*