- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8880C (Mitel Networks Corporation) Integrated DTMF Transceiver(雙音多頻信號（DTMF）收發器（帶電話程序濾波器）) PDF資料下載
參數資料
| 型號： | MT8880C |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Integrated DTMF Transceiver(雙音多頻信號（DTMF）收發器（帶電話程序濾波器）) |
| 中文描述： | 集成雙音多頻收發器（雙音多頻信號（DTMF）的收發器（帶電話程序濾波器）） |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 188K |
| 代理商： | MT8880C |
MT8880C
ISO
2
-CMOS
4-42
Table 6
.
Control Register B Description
Table 7. Status Register Description
BIT
NAME
FUNCTION
DESCRIPTION
b0
BURST
BURST MODE
A logic ‘0’ enables the burst mode. When this mode is
selected, data corresponding to the desired DTMF tone pair
can be written to the Transmit Register resulting in a tone
burst of a specific duration (see AC Characteristics).
Subsequently, a pause of the same duration is induced.
Immediately following the pause, the Status Register is
updated indicating that the Transmit Register is ready for
further instructions and an interrupt will be generated if the
interrupt mode has been enabled. Additionally, if call
progress (CP) mode has been enabled, the burst and pause
duration is increased by a factor of two. When the burst
mode is not selected (logic ‘1’) tone bursts of any desired
duration may be generated.
b1
TEST
TEST MODE
By enabling the test mode (logic’1’), the IRQ/CP pin will
present the delayed steering (inverted) signal from the DTMF
receiver. Refer to Figure 9 (b3 waveform) for details
concerning the output waveform. DTMF mode must be
selected (CRA b1=0) before test mode can be implemented.
b2
S/D
SINGLE /DUAL TONE
GENERATION
A logic ‘0’ will allow Dual Tone Multi-Frequency signals to be
produced. If single tone generation is enabled (logic ‘1’),
either row or column tones (low group or high group) can be
generated depending on the state of b3 in Control Register
B.
b3
C/R
COLUMN/ROW TONES
When used in conjunction with b2 (above) the transmitter
can be made to generate single row or single column
frequencies. A logic ‘0’ will select row frequencies and a logic
‘1’ will select column frequencies.
BIT
NAME
STATUS FLAG SET
STATUS FLAG CLEARED
b0
IRQ
Interrupt has occurred. Bit one (b1)
or bit two (b2) is set.
Interrupt is inactive. Cleared after
Status Register is read.
b1
TRANSMIT DATA
REGISTER EMPTY
(BURST MODE ONLY)
Pause duration has terminated
and transmitter is ready for new
data.
Cleared after Status Register is
read or when in non-burst mode.
b2
RECEIVE DATA
REGISTER FULL
Valid data is in the Receive Data
Register.
Cleared after Status Register is
read.
b3
DELAYED STEERING
Set upon the valid detection of the
absence of a DTMF signal.
Cleared upon the detection of a
valid DTMF signal.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8885AE | Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT8885AN | Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT8885AP | Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT8885 | Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT8885 | Integrated DTMF Transceiver with Power Down and Adaptive Micro Interface(雙音多頻信號（DTMF）收發器（帶電源關閉和自適應微接口）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8880CC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO2-CMOS Integrated DTMFTransceiver |
| MT8880CC/CC-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Integrated DTMFTransceiver |
| MT8880CC-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO2-CMOS Integrated DTMFTransceiver |
| MT8880CE | 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20PDIP - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20PDIP - Rail/Tube 制造商:Zarlink Semiconductor 功能描述:Bulk |
| MT8880CE/CE-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Integrated DTMFTransceiver |
發布緊急采購，3分鐘左右您將得到回復。