參數資料
型號： MSC8122MP8000
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 數字信號處理
英文描述： Quad Core 16-Bit Digital Signal Processor
中文描述： 四核16位數字信號處理器
文件頁數： 84/88頁
文件大?。?/td> 983K
代理商： MSC8122MP8000
MSC8122 Technical Data, Rev. 13
4-2
Freescale Semiconductor
Design Considerations
Decouple the supply using low-ESR capacitors mounted as close as possible to the socket.
Figure 4-1
shows
three capacitors in parallel to reduce the resistance. Three capacitors is a recommended minimum number. If
possible, mount at least one of the capacitors directly below the MSC8122 device.
Each
V
CC
and
V
DD
pin on the MSC8122 device should have a low-impedance path to the board power supply.
Similarly, each
GND
pin should have a low-impedance path to the ground plane. The power supply pins drive
distinct groups of logic on the chip. The
V
CC
power supply should have at least four 0.1 μF by-pass capacitors to
ground located as closely as possible to the four sides of the package. The capacitor leads and associated printed
circuit traces connecting to chip
V
CC
,
V
DD
, and
GND
should be kept to less than half an inch per capacitor lead. A
four-layer board is recommended, employing two inner layers as
V
CC
and
GND
planes.
All output pins on the MSC8122 have fast rise and fall times. PCB trace interconnection length should be
minimized to minimize undershoot and reflections caused by these fast output switching times. This
recommendation particularly applies to the address and data buses. Maximum PCB trace lengths of six inches are
recommended. For the DSI control signals in synchronous mode, ensure that the layout supports the DSI AC
timing requirements and minimizes any signal crosstalk. Capacitance calculations should consider all device loads
as well as parasitic capacitances due to the PCB traces. Attention to proper PCB layout and bypassing becomes
especially critical in systems with higher capacitive loads because these loads create higher transient currents in the
V
CC
,
V
DD
, and
GND
circuits. Pull up all unused inputs or signals that will be inputs during reset.
Special care should be taken to minimize the noise levels on the PLL supply pins. There is one pair of PLL supply
pins:
V
CCSYN
-
GND
SYN
. To ensure internal clock stability, filter the power to the
V
CCSYN
input with a circuit similar to
the one in
Figure 4-2
. For optimal noise filtering, place the circuit as close as possible to
V
CCSYN
. The 0.01-μF
capacitor should be closest to
V
CCSYN
, followed by the 10-μF capacitor, the 10-nH inductor, and finally the 10-
Ω
resistor to
V
DD
. These traces should be kept short and direct. Provide an extremely low impedance path to the
ground plane for
GND
SYN
. Bypass
GND
SYN
to
V
CCSYN
by a 0.01-μF capacitor located as close as possible to the chip
package. For best results, place this capacitor on the backside of the PCB aligned with the depopulated void on the
MSC8122 located in the square defined by positions, L11, L12, L13, M11, M12, M13, N11, N12, and N13.
Figure 4-1.
Core Power Supply Decoupling
Figure 4-2.
V
CCSYN
Bypass
+
-
Power supply
or
Voltage Regulator
(I
min
= 3 A)
High frequency capacitors
(very low ESR and ESL)
Bulk/Tantalum capacitors
with low ESR and ESL
MSC8122
Maximum IR drop
of 15 mV at 1 A
Note
: Use at least three capacitors.
Each capacitor must be at least 150
μ
F.
L
max
= 2 cm
One 0.01 μF capacitor
for every 3 core supply
pads.
1.2 V
V
DD
0.01
μF
10 μF
V
CCSYN
10
Ω
10nH
相關PDF資料
PDF描述
MSC8122TMP4800V Quad Core 16-Bit Digital Signal Processor
MSC8122TMP6400 Quad Core 16-Bit Digital Signal Processor
MSC8122TMP6400V Quad Core 16-Bit Digital Signal Processor
MSC8122TVT4800V Quad Core 16-Bit Digital Signal Processor
MSC8122TVT6400 Quad Core 16-Bit Digital Signal Processor
相關代理商/技術參數
參數描述
MSC8122TMP4800V 功能描述:DSP 16BIT 300MHZ MULTI 431FCPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
MSC8122TMP6400 功能描述:數字信號處理器和控制器 - DSP, DSC PBGA PB 1.2V 105C 400MHZ RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MSC8122TMP6400V 功能描述:DSP 16BIT 400MHZ MULTI 431FCPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
MSC8122TVT4800V 功能描述:IC DSP QUAD 16B 300MHZ 431FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
MSC8122TVT6400 功能描述:DSP 16BIT 400MHZ MULTI 431FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*