參數資料
型號： MSC8103VT1100F
廠商： Freescale Semiconductor
文件頁數： 94/104頁
文件大?。?/td> 0K
描述： IC DSP 16BIT 275MHZ 332-FCPBGA
標準包裝： 90
系列： StarCore
類型： SC140 內核
接口： 通信處理器模塊（CPM）
時鐘速率： 275MHz
非易失內存： 外部
芯片上RAM： 512kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.60V
工作溫度： -40°C ~ 105°C
安裝類型： 表面貼裝
封裝/外殼： 332-BFBGA，F(xiàn)CPBGA
供應商設備封裝： 332-FCBGA（17x17）
包裝： 托盤
Reset, Configuration, and EOnCE Event Signals
MSC8103 Network Digital Signal Processor, Rev. 12
Freescale Semiconductor
1-5
1.3 Reset, Configuration, and EOnCE Event Signals
CLKOUT
Output
Clock Out
The system bus clock.
DLLIN
Input
DLLIN
Synchronizes with an external device.
Note:
When the DLL is disabled, connect this signal to GND.
Table 1-4.
Reset, Configuration, and EOnCE Event Signals
Signal Name
Type
Signal Description
DBREQ
EE01
Input
Output
Debug Request
Determines whether to go into SC140 Debug mode when PORESET is deasserted.
Enhanced OnCE (EOnCE) Event 0
After PORESET is deasserted, you can configure EE0 as an input (default) or an output.
Debug request, enable Address Event Detection Channel 0, or generate an EOnCE event.
Detection by Address Event Detection Channel 0. Used to trigger external debugging equipment.
HPE
EE11
Input
Output
Host Port Enable
When this pin is asserted during PORESET, the Host port is enabled, the system data bus is 32 bits
wide, and the Host must program the reset configuration word.
EOnCE Event 1
After PORESET is deasserted, you can configure EE1 as an input (default) or an output.
Enable Address Event Detection Channel 1 or generate an EOnCE event.
Debug Acknowledge or detection by Address Event Detection Channel 1. Used to trigger external
debugging equipment.
EE21
Input
Output
EOnCE Event 2
After PORESET is deasserted, you can configure EE2 as an input (default) or an output.
Enable Address Event Detection Channel 2 or generate an EOnCE event or enable the Event
Counter.
Detection by Address Event Detection Channel 2. Used to trigger external debugging equipment.
EE31
Input
Output
EOnCE Event 3
After PORESET is deasserted, you can configure EE3 as an input (default) or an output. See the
emulation and debug chapter in the SC140 DSP Core Reference Manual for details on the ERCV
Register.
Enable Address Event Detection Channel 3 or generate one of the EOnCE events.
The DSP has read the EOnCE Receive Register (ERCV). Triggers external debugging equipment.
Table 1-3.
Clock Signals (Continued)
Signal Name
Type
Signal Description
相關PDF資料
PDF描述
RBB10DHRD CONN CARD EXTEND 20POS .050"
VE-253-CW-F1 CONVERTER MOD DC/DC 24V 100W
EEC18DRXS CONN EDGECARD 36POS DIP .100 SLD
VE-25N-CW-F1 CONVERTER MOD DC/DC 18.5V 100W
EMM44DSXS CONN EDGECARD 88POS DIP .156 SLD
相關代理商/技術參數
參數描述
MSC8103VT1200F 功能描述:IC DSP 16BIT 300MHZ 332-FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
MSC81058 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS
MSC81090 制造商:ASI 制造商全稱:ASI 功能描述:NPN SILICON RF POWER TRANSISTOR
MSC81111 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS
MSC81118 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*