參數資料
型號: MQ80C154-36/883D
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44
封裝: CERAMIC, QFP-44
文件頁數: 51/134頁
文件大小: 3805K
代理商: MQ80C154-36/883D
23
8068U–AVR–06/2013
XMEGA A3
Not recommended for new designs -
Use XMEGA A3U series
12. System Control and Reset
12.1
Features
Multiple reset sources for safe operation and device reset
– Power-On Reset
– External Reset
– Watchdog Reset
The Watchdog Timer runs from separate, dedicated oscillator
– Brown-Out Reset
Accurate, programmable Brown-Out levels
– PDI reset
– Software reset
Asynchronous reset
– No running clock in the device is required for reset
Reset status register
12.2
Resetting the AVR
During reset, all I/O registers are set to their initial values. The SRAM content is not reset. Appli-
cation execution starts from the Reset Vector. The instruction placed at the Reset Vector should
be an Absolute Jump (JMP) instruction to the reset handling routine. By default the Reset Vector
address is the lowest Flash program memory address, ‘0’, but it is possible to move the Reset
Vector to the first address in the Boot Section.
The I/O ports of the AVR are immediately tri-stated when a reset source goes active. The reset
functionality is asynchronous, so no running clock is required to reset the device. After the
device is reset, the reset source can be determined by the application by reading the Reset Sta-
tus Register.
12.3
Reset Sources
12.3.1
Power-On Reset
The MCU is reset when the supply voltage VCC is below the Power-on Reset threshold voltage.
12.3.2
External Reset
The MCU is reset when a low level is present on the RESET pin.
12.3.3
Watchdog Reset
The MCU is reset when the Watchdog Timer period expires and the Watchdog Reset is enabled.
The Watchdog Timer runs from a dedicated oscillator independent of the System Clock. For
12.3.4
Brown-Out Reset
The MCU is reset when the supply voltage VCC is below the Brown-Out Reset threshold voltage
and the Brown-out Detector is enabled. The Brown-out threshold voltage is programmable.
12.3.5
PDI reset
The MCU can be reset through the Program and Debug Interface (PDI).
相關PDF資料
PDF描述
MC80C52XXX-20SHXXX 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
MQ80C52CXXX-36SHXXX:D 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
MR80C52TXXX-20/883:D 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CQCC44
MR80C52XXX-30SHXXX:R 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQCC44
MQ80C52EXXX-30 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQFP44
相關代理商/技術參數
參數描述
MQ80C154-L16 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller
MQ80C186-10/BYA 制造商:Rochester Electronics LLC 功能描述:
MQ80C186-12/BYA 制造商:Rochester Electronics LLC 功能描述:
MQ80C186-12/BYC 制造商:Rochester Electronics LLC 功能描述:
MQ80C186-12/R 制造商:Rochester Electronics LLC 功能描述:- Bulk