- 您現在的位置：買賣IC網 > PDF目錄2100 > MPR121QR2 (Freescale Semiconductor)IC CTLR TOUCH SENSOR 20-QFN PDF資料下載
參數資料
| 型號： | MPR121QR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 14/27頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTLR TOUCH SENSOR 20-QFN |
| 產品培訓模塊： | MPR121: Low-Power Touch Sensor |
| 產品目錄繪圖： | MPR121QR2CT |
| 特色產品： | MPR121 Proximity Capacitive Touch Sensor Controller |
| 標準包裝： | 1 |
| 類型： | 電容式，近程傳感器 |
| 輸入數/鍵： | 12 鍵 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 電源電壓： | 1.71 V ~ 3.6 V |
| 電流 - 電源： | 29µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-UFQFN |
| 供應商設備封裝： | 20-QFN（3x3） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 其它名稱： | MPR121QR2DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
MPR121
Sensors
Freescale Semiconductor, Inc.
21
6
MPR121 Serial Communication
6.1
I2C Serial Communications
The MPR121 uses an I2C Serial Interface.The MPR121 operates as a slave that sends and receives data through an I2C two-
wire interface. The interface uses a Serial Data Line (SDA) and a Serial Clock Line (SCL) to achieve bidirectional communication
between master(s) and slave(s). A master (typically a microcontroller) initiates all data transfers to and from the MPR121, and it
generates the SCL clock that synchronizes the data transfer.
The MPR121 SDA line operates as both an input and an open-drain output. A pullup resistor, typically 4.7 k
Ω, is required on SDA.
The MPR121 SCL line operates only as an input. A pullup resistor, typically 4.7 k
Ω, is required on SCL if there are multiple
masters on the two-wire interface, or if the master in a single-master system has an open-drain SCL output.
Each transmission consists of a START condition (Figure 3) sent by a master, followed by the MPR121’s 7-bit slave address plus
R/W bit, a register address byte, one or more data bytes, and finally a STOP condition.
Figure 3. Two-Wire Serial Interface Timing Details
6.2
Slave Address
The MPR121 has selectable slave addresses listed by different ADDR pin connections. This also makes it possible for multiple
MPR121 devices to be used together for channel expansions in a single system.
6.3
Operation with Multiple Master
When operating with multiple masters, bus confusion between I2C masters is sometimes a problem. One way to prevent this is
to avoid using repeated starts to the MPR121. On a I2C bus, once a master issues a start/repeated start condition, that master
owns the bus until a stop condition occurs. If a master that does not own the bus attempts to take control of that bus, then
improper addressing may occur. An address may always be rewritten to fix this problem. Follow I2C protocol for multiple master
configurations.
Table 10. MPR121 Slave Address
ADDR Pin Connection
I2C Address
VSS
0x5A
VDD
0x5B
SDA
0x5C
SCL
0x5D
SCL
SDA
tLOW
tHIGH
tF
tR
tHD STA
tHD DAT
tHD STA
tSU DAT
tSU STA
tBUF
tSU STO
START
CONDITION
STOP
CONDITION
REPEATED START
CONDITION
START
CONDITION
相關PDF資料 |
PDF描述 |
|---|---|
| MX674ALCWI+T | IC ADC 12BIT W/REF 28-SOIC |
| MX7575KN+ | IC ADC 8BIT MPU COMP 18-DIP |
| MX7582KN+ | IC ADC 12BIT 4CH 28-DIP |
| MX7705EWE+ | IC ADC 16BIT 2CH 16-SOIC |
| MX7821KEPP+ | IC ADC 8BIT T/H 20-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR121QR2 | 制造商:Freescale Semiconductor 功能描述:IC CAPACITIVE TOUCH SENSOR CTRL QFN-20 |
| MPR121QR2-CUT TAPE | 制造商:Freescale 功能描述:MPR121 Series 3.6 V 29 ? Proximity Capacitive Touch Sensor Controller - QFN-20 |
| MPR1487 | 制造商:MISC. COMMERCIAL HRD 功能描述: |
| MPR181EJ | 功能描述:電容觸摸傳感器 8 POSITION TOUCH PAD RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| MPR181EJR2 | 功能描述:電容觸摸傳感器 8 POSITION TOUCH PAD RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
發布緊急采購，3分鐘左右您將得到回復。