- 您現在的位置：買賣IC網 > PDF目錄2100 > MPR032EPR2 (Freescale Semiconductor)IC CTLR TOUCH SENSOR 8-DFN PDF資料下載
參數資料
| 型號： | MPR032EPR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 4/33頁 |
| 文件大小： | 0K |
| 描述： | IC CTLR TOUCH SENSOR 8-DFN |
| 產品培訓模塊： | MPR03x - Low-Power Proximity Sensors |
| 特色產品： | MPR03x Proximity Capacitive Touch Sensor Controllers |
| 標準包裝： | 1 |
| 類型： | 電容性 |
| 觸摸面板接口： | 2 線 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 數據速率/采樣率 (SPS，BPS)： | 400k |
| 電源電壓： | 1.71 V ~ 2.75 V |
| 電流 - 電源： | 43µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-UFDFN |
| 供應商設備封裝： | 8-QFN-D（2x2） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 其它名稱： | MPR032EPR2DKR |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MPR03X
Sensors
12
Freescale Semiconductor
5
Output Mechanisms
5.1
Introduction
The MPR03X has three outputs: the touch status, values from the second level filter (Section 8.3), and the calibrated baseline
values. The application can either use the touch status or a combination of second level filter data with the baseline data to
determine when a touch occurs.
5.2
Touch Status
Each Electrode has an associated single bit that denotes whether or not the pad is currently touched. This output is generated
using the touch threshold and release threshold registers to determine when a pad is considered touched or untouched.
Configuration of this system is discussed in Section 9.
5.2.1
The Touch Pad Status Register is a read only register for determining the current status of the touch pad. The I2C slave address
of the Touch Pad Status Register is 0x00.
Figure 17. Touch Status Register
7
6
543210
R
OCF
0
E2S
E1S
E0S
W
Reset:
0
000000
= Unimplemented
Table 6. Touch Pad Status Register Field Descriptions
Field
Description
7
OCF
Over Current Flag – The Over Current Flag shows when too much current is on the REXT
pin. If it is set all other status flags and registers are cleared and the device is set to Stop
mode. When OCF is set, the MPR03X cannot be put back into a Run mode.
0 – Current is within limits.
1 – Current is above limits. Writing a 1 to this field will clear the OCF.
2
E2S
Electrode 2 Status – The Electrode 2 Status bit shows touched or not touched.
0 – Not Touched
1 – Touched
1
E1S
Electrode 1 Status – The Electrode 1 Status bit shows touched or not touched.
0 – Not Touched
1 – Touched
0
E0S
Electrode 0 Status – The Electrode 0 Status bit shows touched or not touched.
0 – Not Touched
1 – Touched
相關PDF資料 |
PDF描述 |
|---|---|
| MPR083QR2 | IC CTLR TOUCH SENSOR PROX 16-QFN |
| MPR084QR2 | IC CTLR TOUCH SENSOR PROX 16-QFN |
| MPR121QR2 | IC CTLR TOUCH SENSOR 20-QFN |
| MX674ALCWI+T | IC ADC 12BIT W/REF 28-SOIC |
| MX7575KN+ | IC ADC 8BIT MPU COMP 18-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR03X | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03X_09 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XEJ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XEP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XQ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
發布緊急采購，3分鐘左右您將得到回復。