- 您現在的位置：買賣IC網 > PDF目錄2100 > MPR032EPR2 (Freescale Semiconductor)IC CTLR TOUCH SENSOR 8-DFN PDF資料下載
參數資料
| 型號： | MPR032EPR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 13/33頁 |
| 文件大小： | 0K |
| 描述： | IC CTLR TOUCH SENSOR 8-DFN |
| 產品培訓模塊： | MPR03x - Low-Power Proximity Sensors |
| 特色產品： | MPR03x Proximity Capacitive Touch Sensor Controllers |
| 標準包裝： | 1 |
| 類型： | 電容性 |
| 觸摸面板接口： | 2 線 |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行 |
| 數據速率/采樣率 (SPS，BPS)： | 400k |
| 電源電壓： | 1.71 V ~ 2.75 V |
| 電流 - 電源： | 43µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-UFDFN |
| 供應商設備封裝： | 8-QFN-D（2x2） |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 其它名稱： | MPR032EPR2DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MPR03X
Sensors
20
Freescale Semiconductor
8Filtering
8.1
Introduction
The MPR03X has three levels of filtering. The first and second level filters will allow the application to condition the signal for
undesired input variation. The third level filter can be configured to reject touch stimulus and be used as a baseline for touch
detection. Each level of filtering will be further described in this section.
8.2
First Level
The first level filter is designed to filter high frequency noise by averaging samples taken over short periods of time. The number
of samples can be configured to equal a set of values ranging from 6 to 34 samples. This value is set by the FFI in the AFE
Configuration Register (Section 7.4.1). The timing of this filter is also determined by the configuration of the electrode charge time
in the Filter Configuration Register (Section 8.3.1).
Note that the electrode charge time must be configured for the capacitance in the application. The resulting value will affect the
period of the first level filter.
8.3
Second Level
The second level filter is designed to filter low frequency noise and reject false touches due to inconsistent data. The number of
samples can be configured to equal a set of values ranging from 4 to 18. This value is set by the SFI in the Filter Configuration
Register (Section 8.3.1). The timing of this filter is also determined by the configuration of ESI in the Filter Configuration Register
Note that the ESI (Electrode Sample Interval) must be configured to accommodate the low power requirements of a system.
Thus, the resulting value will affect the period of the second level filter.
The raw data from the second level of filtering is output in the Filtered Data High and Filtered Data Low registers, as shown in
8.3.1
The Filter Configuration register is used to set the electrode charge/discharge time (CDT), second level filter iteration (SFI), and
electrode sample intervals (ESI). The address of the Electrode Configuration Register is 0x43.
Figure 26. Filter Configuration Register
7
6
543210
R
CDT
SFI
ESI
W
Reset:
0
100100
= Unimplemented
相關PDF資料 |
PDF描述 |
|---|---|
| MPR083QR2 | IC CTLR TOUCH SENSOR PROX 16-QFN |
| MPR084QR2 | IC CTLR TOUCH SENSOR PROX 16-QFN |
| MPR121QR2 | IC CTLR TOUCH SENSOR 20-QFN |
| MX674ALCWI+T | IC ADC 12BIT W/REF 28-SOIC |
| MX7575KN+ | IC ADC 8BIT MPU COMP 18-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPR03X | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03X_09 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XEJ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XEP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
| MPR03XQ | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller |
發布緊急采購，3分鐘左右您將得到回復。