參數資料
型號: MPE603PFE200LX
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 32-BIT, 200 MHz, RISC PROCESSOR, CQFP240
封裝: 32 X 32 MM, 0.50 MM PITCH, CERAMIC, QFP-240
文件頁數: 18/36頁
文件大?。?/td> 201K
代理商: MPE603PFE200LX
PRELIMINAR
Y
MOTOROLA
EC603e Microprocessor Hardware Specifications (PID7v)
25
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
1.8.2 PLL Power Supply Filtering
The AVdd power signal is provided on the PID7v to provide power to the clock generation phase-locked
loop. To ensure stability of the internal clock, the power supplied to the AVdd input signal should be ltered
using a circuit similar to the one shown in Figure 13. The circuit should be placed as close as possible to the
AVdd pin to ensure it lters out as much noise as possible. The 0.1
F capacitor should be closest to the
AVdd pin, followed by the 10
F capacitor, and nally the 10 resistor to Vdd. These traces should be kept
short and direct.
Figure 13. PLL Power Supply Filter Circuit
1.8.3 Decoupling Recommendations
Due to the PID7v’s dynamic power management feature, large address and data buses, and high operating
frequencies, the PID7v can generate transient power surges and high frequency noise in its power supply,
especially while driving large capacitive loads. This noise must be prevented from reaching other
components in the PID7v system, and the PID7v itself requires a clean, tightly regulated source of power.
Therefore, it is recommended that the system designer place at least one decoupling capacitor at each Vdd
and OVdd pin of the PID7v. It is also recommended that these decoupling capacitors receive their power
from separate Vdd, OVdd, and GND power planes in the PCB, utilizing short traces to minimize inductance.
These capacitors should vary in value from 220 pF to 10
F to provide both high- and low-frequency
ltering, and should be placed as close as possible to their associated Vdd or OVdd pin. Suggested values
for the Vdd pins—220 pF (ceramic), 0.01
F (ceramic), and 0.1 F (ceramic). Suggested values for the
OVdd pins—0.01
F (ceramic), 0.1 F (ceramic), and 10 F (tantalum). Only SMT (surface mount
technology) capacitors should be used to minimize lead inductance.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the Vdd and OVdd planes, to enable quick recharging of the smaller chip capacitors. These bulk
capacitors should also have a low ESR (equivalent series resistance) rating to ensure the quick response time
necessary. They should also be connected to the power and ground planes through two vias to minimize
inductance. Suggested bulk capacitors—100
F (AVX TPS tantalum) or 330 F (AVX TPS tantalum).
1.8.4 Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to Vdd. Unused active high inputs should be connected to
GND. All NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external Vdd, OVdd, and GND pins of the PID7v.
Vdd
AVdd
10
10
F
0
.1
F
GND
相關PDF資料
PDF描述
MPE603PRX200LX 32-BIT, 200 MHz, RISC PROCESSOR, CBGA255
MPE603PFE166LX 32-BIT, 167 MHz, RISC PROCESSOR, CQFP240
MPE603RRX300LX 32-BIT, 300 MHz, RISC PROCESSOR, CBGA255
MPM21CUA650B 32-BIT, 650 MHz, MICROPROCESSOR, XMA
MPM21CUA550B 32-BIT, 550 MHz, MICROPROCESSOR, XMA
相關代理商/技術參數
參數描述
MPE603RRX200LC 制造商:Freescale Semiconductor 功能描述:
MPE603RRX266LC 制造商:Motorola Inc 功能描述:
MPE-60S 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Single Output, 60W Compact, Enclosed AC/DC Power Supplies
MPE-60S-05 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Single Output, 60W Compact, Enclosed AC/DC Power Supplies
MPE-60S-12 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Single Output, 60W Compact, Enclosed AC/DC Power Supplies