1 tUI, t
<li id="azdj6"><wbr id="azdj6"><xmp id="azdj6"></xmp></wbr></li>
參數資料
型號: MPC5200VR400BR2
廠商: Freescale Semiconductor
文件頁數: 26/72頁
文件大?。?/td> 0K
描述: IC MPU 32BIT 400MHZ 272-PBGA
標準包裝: 500
系列: MPC52xx
核心處理器: e300
芯體尺寸: 32-位
速度: 400MHz
連通性: CAN,EBI/EMI,以太網,I²C,IrDA,J1850,SPI,UART/USART,USB
外圍設備: AC'97,DMA,I²S,POR,PWM,WDT
輸入/輸出數: 56
程序存儲器類型: 外部程序存儲器
RAM 容量: 16K x 8
電壓 - 電源 (Vcc/Vdd): 1.42 V ~ 1.58 V
振蕩器型: 內部
工作溫度: 0°C ~ 70°C
封裝/外殼: 272-BBGA
包裝: 帶卷 (TR)
MPC5200B Data Sheet, Rev. 4
32
Freescale Semiconductor
NOTES:
1 tUI, tMLI, tLI indicate sender-to-recipient or recipient-to-sender interlocks. That is, one agent (sender or recipient) is waiting for
the other agent to respond with a signal before proceeding.
tUI is an unlimited interlock that has no maximum time value.
tMLI is a limited time-out that has a defined minimum.
tLI is a limited time-out that has a defined maximum.
2 All timing parameters are measured at the connector of the drive to which the parameter applies. For example, the sender shall
stop generating STROBE edges tRFS after negation of DMARDY. STROBE and DMARDY timing measurements are taken at
the connector of the sender. Even though the sender stops generating STROBE edges, the receiver may receive additional
STROBE edges due to propagation delays. All timing measurement switching points (low to high and high to low) are taken at
1.5 V.
t AZ
10
10
10
Maximum time allowed for output drivers to release
from being asserted or negated
A8.36
tZAH
20
20
20
Minimum delay time required for output drivers to
assert or negate from released state
A8.37
t ZAD
0—0—0—
A8.38
t ENV
20
70
20
70
20
70
Envelope time—from DMACK to STOP and
HDMARDY during data out burst initiation.
A8.39
t SR
50
30
20
STROBE to DMARDY time, if DMARDY is negated
before this long after STROBE edge, the recipient
receives no more than one additional data word.
A8.40
t RFS
75
60
50
Ready-to-Final STROBE time—no STROBE edges
are sent this long after negation of DMARDY.
A8.41
t RP
160
125
100
Ready-to-Pause time—the time recipient waits to
initiate pause after negating DMARDY.
A8.42
t IORDYZ
20
20
20
Pull-up time before allowing IORDY to be released.
A8.43
t ZIORDY
0
0
0
Minimum time drive waits before driving IORDY
A8.44
t ACK
20
20
20
Setup and hold times for DMACK, before assertion or
negation.
A8.45
t SS
50
50
50
Time from STROBE edge to negation of DMARQ or
assertion of STOP, when sender terminates a burst.
A8.46
Table 29. Ultra DMA Timing Specification (continued)
Sym
MODE 0
(ns)
MODE 1
(ns)
MODE 2
(ns)
Comment
SpecID
Min
Max
Min
Max
Min
Max
相關PDF資料
PDF描述
MCF52211CVM80 IC MCU 128K FLASH 80MHZ 81MAPBGA
MC9S08SL16CTL MCU 16KB FLASH SLIC 28TSSOP
VE-BNV-CU-F3 CONVERTER MOD DC/DC 5.8V 200W
VE-BNT-CU-F1 CONVERTER MOD DC/DC 6.5V 200W
VE-BNR-CU-F2 CONVERTER MOD DC/DC 7.5V 200W
相關代理商/技術參數
參數描述
MPC52100J 功能描述:厚膜電阻器 - 透孔 RoHS:否 制造商:Caddock 電阻:27 kOhms 容差:1 % 功率額定值:8 W 溫度系數:50 PPM / C 系列:MS 端接類型:Axial 電壓額定值:2 kV 工作溫度范圍:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封裝:Bulk
MPC52100J 制造商:TE Connectivity 功能描述:RESISTOR 5W 10R
MPC52100J 制造商:TE Connectivity 功能描述:RESISTOR THICK FILM 10OHM 5W 5% 制造商:TE Connectivity 功能描述:RESISTOR, THICK FILM, 10 OHM, 5W, 5%
MPC52101J 功能描述:厚膜電阻器 - 透孔 MPC5 100R 5% RoHS:否 制造商:Caddock 電阻:27 kOhms 容差:1 % 功率額定值:8 W 溫度系數:50 PPM / C 系列:MS 端接類型:Axial 電壓額定值:2 kV 工作溫度范圍:- 15 C to + 275 C 尺寸:8.89 mm Dia. x 23.11 mm L 封裝:Bulk
MPC52101J 制造商:TE Connectivity 功能描述:RESISTOR 5W 100R