2
MN101C62D, MN101C62F
Timer Counter
(Continue)
Timer counter 7 : 16-bit
×
1
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
evevt, pulse width measurement, input capture, generation of real time)
Clock source
·····················
1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
Interrupt source
················
coincidence with compare register 7 (2 lines)
Watchdog timer
Interrupt source
················
1/65536, 1/262144, 1/1048576 of system clock frequency
Timer counter 8 : 16-bit
×
1
(square-wave output, 16-bit PWM output (cycle / duty continuous variable), event count, synchronous output
evevt, pulse width measurement, input capture, generation of real time)
Clock source
·····················
1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC
oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency
Interrupt source
················
coincidence with compare register 7 (2 lines)
Watchdog timer
Interrupt source
················
1/65536, 1/262144, 1/1048576 of system clock frequency
Serial Interface
Serial 0 : synchronous type/UART (full-duplex)
×
1
Clock source
·····················
1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2;
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
Serial 1 : synchronous type/UART (full-duplex)
×
1
Clock source
·····················
1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
1/2,1/8 of timer counter 2 output;
1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency
Serial 2 : synchronous type / single-master I
2
C
Clock source
·····················
1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3;
1/2, 1/4, 1/8, 1/32 of OSC oscillation clock frequency
I/O Pins
68
Common use
Specified pull-up resistor available
Input/output selectable (bit unit)
I/O
A/D Inputs
Special Ports
10-bit
×
8-ch. (with S/H)
Buzzer output, remote control carrier signal output, high-current drive port
Electrical Characteristics
Supply current
Limit
Symbol
Condition
min
typ
max
Unit
Parameter
IDD1
fosc = 20 MHz, VDD = 5 V
18
30
mA
IDD2
fx = 32 kHz, VDD = 3 V
30
60
μ
A
IDD3
fx = 32 kHz, VDD = 3 V, Ta = 25
°
C
6
8
μ
A
IDD4
fx = 32 kHz, VDD = 3 V, Ta = 85
°
C
30
μ
A
IDD5
VDD = 5 V, Ta = 25
°
C
2
μ
A
IDD6
VDD = 5 V, Ta = 85
°
C
50
μ
A
Operating supply current
Supply current at HALT
Supply current at STOP
See the next page for pin assignment and support tool.
MAD00020EEM