- 您現在的位置：買賣IC網 > PDF目錄382337 > MMBD355LT1 (樂山無線電股份有限公司) Dual Hot Carrier Mixer Diodes PDF資料下載
參數資料
| 型號： | MMBD355LT1 |
| 廠商： | 樂山無線電股份有限公司 |
| 英文描述： | Dual Hot Carrier Mixer Diodes |
| 中文描述： | 雙熱載流子二極管混頻器 |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 41K |
| 代理商： | MMBD355LT1 |
MMBD352LT1 MMBD353LT1 MMBD354LT1 MMBD355LT1
http://onsemi.com
3
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25
°
C,
one can calculate the power dissipation of the device which
in this case is 225 milliwatts.
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the
total design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOT–23
mm
inches
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
SOT–23 POWER DISSIPATION
PD =
TJ(max) – TA
R
θ
JA
PD =
150
°
C – 25
°
C
556
°
C/W
= 225 milliwatts
The power dissipation of the SOT–23 is a function of the
pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipa-
tion. Power dissipation for a surface mount device is deter-
mined by TJ(max), the maximum rated junction temperature
of the die, R
θ
JA, the thermal resistance from the device
junction to ambient, and the operating temperature, TA.
Using the values provided on the data sheet for the SOT–23
package, PD can be calculated as follows:
The 556
°
C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed
circuit board to achieve a power dissipation of 225 milli-
watts. There are other alternatives to achieving higher
power dissipation from the SOT–23 package. Another
alternative would be to use a ceramic substrate or an
aluminum core board such as Thermal Clad
. Using a
board material such as Thermal Clad, an aluminum core
board, the power dissipation can be doubled using the same
footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the
rated temperature of the device. When the entire device is
heated to a high temperature, failure to complete soldering
within a short time could result in device failure. There-
fore, the following items should always be observed in
order to minimize the thermal stress to which the devices
are subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause exces-
sive thermal shock and stress which can result in damage
to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MMBD353LT1 | Dual Hot Carrier Mixer Diodes |
| MMBT2131T1 | General Purpose Transistors |
| MMBT2131T3 | General Purpose Transistors |
| MMBT2132T1 | 43632 LOGIC CELLS 12 ROCKET IOS 2 POWER |
| MMBT2132T3 | General Purpose Transistors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMBD355LT1G | 功能描述:整流器 7V 225mW Dual Common Anode RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| MMBD355W | 制造商:PANJIT 制造商全稱:Pan Jit International Inc. 功能描述:SURFACE MOUNT HIGH FREQUENCY SCHOTTKY DIODE |
| MMBD4148 | 功能描述:整流器 High Cond Ult Fst Di RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| MMBD4148 _R1 _00001 | 制造商:PanJit Touch Screens 功能描述: |
| MMBD4148 MCC | 制造商:MCC 功能描述:HIGH SPEED 75V SMD (Surface Mount) Switching Diode SOT-23 Single 350mW 制造商:MCC 功能描述:HIGH SPEED 75V SMD (Surface Mount) Switching Diode SOT-23 Single 350mW - free partial T/R at 500. |
發布緊急采購，3分鐘左右您將得到回復。