- 您現在的位置：買賣IC網 > PDF目錄45334 > MM908E626AVDWB (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E626AVDWB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 17.90 X 7.50 MM, 0.65 MM PITCH, LEAD FREE, PLASTIC, SOIC-54 |
| 文件頁數： | 17/44頁 |
| 文件大?。?/td> | 833K |
| 代理商： | MM908E626AVDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
908E626
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The LIN transmitter circuitry is enabled by setting the
PSON bit in the System Control Register (SYSCTL). If the
transmitter works in the current limitation region, the LINCL
bit in the System Status Register (SYSSTAT) is set. Due to
excessive power dissipation in the transmitter, software is
advised to monitor this bit and turn the transmitter off
immediately.
TXD Pin
The TXD pin is the MCU interface to control the state of the
LIN transmitter (see Figure , page 2). When TXD is LOW, LIN
output is low (dominant state). When TXD is HIGH, the LIN
output MOSFET is turned off. The TXD pin has an internal
pullup current source in order to set the LIN bus in recessive
state in the event, for instance, the microcontroller could not
control it during system power-up or power-down.
RXD Pin
The RXD transceiver pin is the MCU interface, which
reports the state of the LIN bus voltage. LIN HIGH (recessive
state) is reported by a high level on RXD, LIN LOW (dominant
state) by a low level on RXD.
STOP Mode/Wake-up Feature
During STOP mode operation the transmitter of the
physical layer is disabled. The receiver pin is still active and
able to detect wake-up events on the LIN bus line.If LIN
interrupt is enabled (LINIE bit in the Interrupt Mask Register
is set), a falling edge on the LIN line causes an interrupt. This
interrupt switches on the main voltage regulator and
generates a system wake-up.
Analog Multiplexer/ADOUT Pin
The ADOUT pin is the analog output interface to the ADC
of the MCU (see Figure , page 2). An analog multiplexer is
used to read six internal diagnostic analog voltages.
Current Recopy
The analog multiplexer is connected to the four low side
current sense circuits of the half-bridges. These sense
circuits offer a voltage proportional to the current through the
low side MOSFET. High or low resolution is selectable: 5.0V/
2.5A or 5.0V/500mA, respectively. (Refer to Half-Bridge
Temperature Sensor
The 908E626 includes an on-chip temperature sensor.
This sensor offers a voltage that is proportional to the actual
chip junction temperature.
VSUP Prescaler
The VSUP prescaler permits the reading or measurement
of the external supply voltage. The output of this voltage is
VSUP/RATIOVSUP.
The different internal diagnostic analog voltages can be
selected with the ADMUX Register.
Analog Multiplexer Configuration Register (ADMUX)
Bit7
6
5
4
3
2
1
Bit0
Read
Write
Reset
SS3, SS2, SS1, and SS0—A/D Input Select Bits
These read/write bits select the input to the ADC in the
microcontroller according to Table 7, page 24. Reset clears
SS3, SS2, SS1, and SS0 bits.
Table 7. Analog Multiplexer Configuration Register
Power Output Register (POUT)
Bit7 6
5
4
3
2
1
Bit0
Read
Write
Reset
16.
This bit must always be set to 0.
Register Name and Address: ADMUX - $07
0
SS3
SS2
SS1
SS0
0
SS3
SS2
SS1
SS0
Channel
0
Current Recopy HB1
0
1
Current Recopy HB2
0
1
0
Current Recopy HB3
0
1
Current Recopy HB4
0
1
0
VSUP Prescaler
0
1
0
1
Temperature Sensor
0
1
0
Not Used
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Register Name and Address: POUT - $0b
0
0
0
0
HVDDO
N
0
0
Notes
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E626AVEK | FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| MMAD1108R2 | 0.4 A, 8 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1504A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1505A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD2837LT3 | 0.15 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。