- 您現在的位置：買賣IC網 > PDF目錄359176 > MM908E626AVDWB (飛思卡爾半導體(中國)有限公司) Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication PDF資料下載
參數資料
| 型號： | MM908E626AVDWB |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 中文描述： | 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 303K |
| 代理商： | MM908E626AVDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
908E626
16
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
Important
VDDA is the supply for the ADC and should be
tied to the same potential as EVDD via separate traces. VSSA
is the ground terminal for the ADC and should be tied to the
same potential as EVSS via separate traces.
For details refer to the 68HC908EY16 datasheet.
MCU Power Supply Terminals (EVDD and EVSS)
EVDD
and EVSS
are the power supply and ground
terminals. The MCU operates from a single power supply.
Fast signal transitions on MCU terminals place high, short-
duration current demands on the power supply. To prevent
noise problems, take special care to provide power supply
bypassing at the MCU.
For details refer to the 68HC908EY16 datasheet.
Test Terminal (FLSVPP)
For test purposes only. Do not connect in the application.
Exposed Pad Terminal
The exposed pad terminal on the bottom side of the package
conducts heat from the chip to the PCB board. For thermal
performance the pad must be soldered to the PCB board. It is
recommended that the pad be connected to the ground
potential.
ANALOG DIE DESCRIPTION
Interrupts
The 908E626 has five different interrupt sources as
described in the following paragraphs. The interrupts can be
disabled or enabled via the SPI. After reset all interrupts are
automatically disabled.
Low-Voltage Interrupt
The Low-Voltage Interrupt (LVI) is related to the external
supply voltage, V
SUP
. If this voltage falls below the LVI
threshold, it will set the LVI flag. If the low-voltage interrupt is
enabled, an interrupt will be initiated.
With LVI the H-Bridges (high-side MOSFET only) are
switched off. All other modules are not influenced by this
interrupt.
High-Voltage Interrupt
The High-Voltage Interrupt (HVI) is related to the external
supply voltage, V
SUP
. If this voltage rises above the HVI
threshold, it will set the HVI flag. If the High-Voltage Interrupt is
enabled, an interrupt will be initiated.
With HVI the H-Bridges (high-side MOSFET only) are
switched off. All other modules are not influenced by this
interrupt.
High-Temperature Interrupt
The High-Temperature Interrupt (HTI) is generated by the
on-chip temperature sensors. If the chip temperature is above
the HTI threshold, the HTI flag will be set. If the High-
Temperature Interrupt is enabled, an interrupt will be initiated.
LIN Interrupt
If the LINIE bit is set, a falling edge on the LIN terminal will
generate an interrupt.
Overcurrent Interrupt
If an overcurrent condition on a half-bridge or the HVDD
output is detected and the OCIE bit is set and an interrupt
generated.
Interrupt Flag Register (IFR)
LINF
—
LIN Flag Bit
This read/write flag is set on the falling edge at the LIN data
line. Clear LINF by writing a logic [1] to LINF. Reset clears the
LINF bit. Writing a logic [0] to LINF has no effect.
1 = Falling edge on LIN data line has occurred.
0 = Falling edge on LIN data line has not occurred since
last clear.
HTF
—
High-Temperature Flag Bit
This read/write flag is set on
a high-temperature condition.
Clear HTF by writing a logic [1] to HTF. If a high-temperature
condition is still present while writing a logic [1] to HTF, the
writing has no effect. Therefore, a high-temperature interrupt
cannot be lost due to inadvertent clearing of HTF. Reset clears
the HTF bit. Writing a logic [0] to HTF has no effect.
1 = High-temperature condition has occurred.
0 = High-temperature condition has not occurred.
Register Name and Address: IFR - $05
Bit7
6
5
4
3
2
1
Bit0
Read
0
0
LINF
HTF
LVF
HVF
OCF
0
Write
Reset
0
0
0
0
0
0
0
0
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E626R2 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MMA1200D | Surface Mount Micromachined Accelerometer(表面安裝微電機加速計) |
| MMA1200 | Surface Mount Micromachined Accelerometer |
| MMA1210D | Surface Mount Micromachined Accelerometer(表面安裝微電機加速計) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。