- 您現在的位置：買賣IC網 > PDF目錄359176 > MM908E626AVDWB (飛思卡爾半導體(中國)有限公司) Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication PDF資料下載
參數資料
| 型號： | MM908E626AVDWB |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 中文描述： | 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 14/32頁 |
| 文件大?。?/td> | 303K |
| 代理商： | MM908E626AVDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
908E626
14
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 908E626 device was designed and developed as a
highly integrated and cost-effective solution for automotive and
industrial applications. For automotive body electronics, the
908E626 is well suited to perform stepper motor control, e.g. for
climate or light-levelling control via a 3-wire LIN bus.
This device combines an standard HC08 MCU core
(68HC908EY16) with flash memory together with a
SMARTMOS
IC chip. The
SMARTMOS
IC chip combines
power and control in one chip. Power switches are provided on
the
SMARTMOS
IC configured as four half-bridge outputs.
Other ports are also provided including a selectable HVDD
terminal. An internal voltage regulator is provided on the
SMARTMOS
IC chip, which provides power to the MCU chip.
Also included in this device is a LIN physical layer, which
communicates using a single wire. This enables the device to
be compatible with 3-wire bus systems, where one wire is used
for communication, one for battery, and the third for ground.
FUNCTIONAL TERMINAL DESCRIPTION
See
Figure 1, 908E626 Simplified Internal Block Diagram
,
page 2, for a graphic representation of the various terminals
referred to in the following paragraphs. Also, see the terminal
diagram on
page 3
for a depiction of the terminal locations on
the package.
Port A I/O Terminals
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. PTA0:PTA4 are shared with the keyboard interrupt
terminals, KBD0:KBD4.
The PTA5/SPSCK terminal is not accessible in this device
and is internally connected to the SPI clock terminal of the
analog die. The PTA6/
SS
terminal is likewise not accessible.
For details refer to the 68HC908EY16 datasheet.
Port B I/O Terminals
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. All terminals are shared with the ADC module. The
PTB6:PTB7 terminals are also shared with the Timer B module.
PTB0/AD0 is internally connected to the ADOUT terminal of
the analog die, allowing diagnostic measurements to be
calculated; e.g., current recopy, V
SUP
, etc. The PTB2/AD2
terminal is not accessible in this device.
For details refer to the 68HC908EY16 datasheet.
Port C I/O Terminals
These terminals are special-function, bidirectional I/O port
terminals that are shared with other functional modules in the
MCU. For example, PTC2:PTC4 are shared with the ICG
module.
PTC0/MISO and PTC1/MOSI are not accessible in this
device and are internally connected to the MISO and MOSI SPI
terminals of the analog die.
For details refer to the 68HC908EY16 datasheet.
Port D I/O Terminals
PTD1/TACH1 and PTD0/TACH0/BEMF are special-
function, bidirectional I/O port terminals that can also be
programmed to be timer terminals.
In step motor applications the PTD0 terminal should be
connected to the BEMF output of the analog die in order to
evaluate the BEMF signal with a special BEMF module of the
MCU.
PTD1 terminal is recommended for use as an output terminal
for generating the FGEN signal (PWM signal) if required by the
application.
Port E I/O Terminal
PTE1/RXD and PTE0/TXD are special-function,
bidirectional I/O port terminals that can also be programmed to
be enhanced serial communication.
PTE0/TXD is internally connected to the TXD terminal of the
analog die.
The connection for the receiver must be done
externally.
External Interrupt Terminal (
IRQ
)
The
IRQ
terminal is an asynchronous external interrupt
terminal. This terminal contains an internal pullup resistor that
is always activated, even when the
IRQ
terminal is pulled LOW.
For details refer to the 68HC908EY16 datasheet.
External Reset Terminal (
RST
)
A logic [0] on the
RST
terminal forces the MCU to a known
startup state.
RST
is bidirectional, allowing a reset of the entire
system. It is driven LOW when any internal reset source is
asserted.
This terminal contains an internal pullup resistor that is
always activated, even when the reset terminal is pulled LOW.
For details refer to the 68HC908EY16 datasheet.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E626R2 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MMA1200D | Surface Mount Micromachined Accelerometer(表面安裝微電機加速計) |
| MMA1200 | Surface Mount Micromachined Accelerometer |
| MMA1210D | Surface Mount Micromachined Accelerometer(表面安裝微電機加速計) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。