- 您現在的位置：買賣IC網 > PDF目錄1954 > MM908E625ACDWB (Freescale Semiconductor)IC QUAD HALF BRDG MCU/LIN 54SOIC PDF資料下載
參數資料
| 型號： | MM908E625ACDWB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 14/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC QUAD HALF BRDG MCU/LIN 54SOIC |
| 標準包裝： | 26 |
| 應用： | 自動鏡像控制 |
| 核心處理器： | HC08 |
| 程序存儲器類型： | 閃存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 輸入/輸出數： | 13 |
| 電源電壓： | 8 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 包裝： | 管件 |
| 供應商設備封裝： | 54-SOICW-EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
INTERRUPT FLAG REGISTER (IFR)
Hall-Effect Sensor Input Pin Flag Bit (HPF)
This read/write flag is set depending on Run/Stop mode.
RUN Mode
An interrupt will be generated when a state change on any
enabled Hall-effect sensor input pin is detected. Clear HPF
by writing a Logic [1] to HPF. Reset clears the HPF bit.
Writing a Logic [0] to HPF has no effect.
1 = State change on the hallflags detected
0 = No state change on the hallflags detected
STOP Mode
An interrupt will be generated when AWDCC is set and a
current above the threshold is detected on any enabled Hall-
effect sensor input pin. Clear HPF by writing a Logic [1] to
HPF. Reset clears the HPF bit. Writing a Logic [0] to HPF has
no effect.
1 = One or more of the selected Hall-effect sensor input
pins had been pulled HIGH
0 = None of the selected Hall-effect sensor input pins
has been pulled HIGH
LIN Flag Bit (LINF)
This read/write flag is set on the falling edge at the LIN
data line. Clear LINF by writing a Logic [1] to LINF. Reset
clears the LINF bit. Writing a Logic [0] to LINF has no effect.
1 = Falling edge on LIN data line has occurred
0 = Falling edge on LIN data line has not occurred since
last clear
High-Temperature Flag Bit (HTF)
This read/write flag is set on a high temperature condition.
Clear HTF by writing a Logic [1] to HTF. If a high temperature
condition is still present while writing a Logic [1] to HTF, the
writing has no effect. Therefore, a high temperature interrupt
cannot be lost due to inadvertent clearing of HTF. Reset
clears the HTF bit. Writing a Logic [0] to HTF has no effect.
1 = High temperature condition has occurred
0 = High temperature condition has not occurred
Low Voltage Flag Bit (LVF)
This read/write flag is set on a low voltage condition. Clear
LVF by writing a Logic [1] to LVF. If a low voltage condition is
still present while writing a Logic [1] to LVF, the writing has no
effect. Therefore, a low voltage interrupt cannot be lost due
to inadvertent clearing of LVF. Reset clears the LVF bit.
Writing a Logic [0] to LVF has no effect.
1 = Low voltage condition has occurred
0 = Low voltage condition has not occurred
High Voltage Flag Bit (HVF)
This read/write flag is set on a high voltage condition.
Clear HVF by writing a Logic [1] to HVF. If high voltage
condition is still present while writing a Logic [1] to HVF, the
writing has no effect. Therefore, a high voltage interrupt
cannot be lost due to inadvertent clearing of HVF. Reset
clears the HVF bit. Writing a Logic [0] to HVF has no effect.
1 = High voltage condition has occurred
0 = High voltage condition has not occurred
Over-current Flag Bit (OCF)
This read-only flag is set on an over-current condition.
Reset clears the OCF bit. To clear this flag, write a Logic [1]
to the appropriate over-current flag in the SYSSTAT
Register. See Figure 10,illustrating the three signals
triggering the OCF.
1 = High current condition has occurred
0 = High current condition has not occurred
Figure 10. Principal Implementation for OCF
Register Name and Address: IFR - $05
Bits
7
6
5
4
3
2
1
0
Read
0
HPF
LINF
HTF
LVF
HVF
OCF
0
Write
Reset
0
OCF
HVDD_OCF
HS_OCF
HB_OCF
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E626AVDWB | IC STEPPER MOTOR DRIVER 54-SOIC |
| MM912F634BV1AER2 | IC MCU 16BIT 32KB FLASH 48LQFP |
| MM912H634CM1AER2 | IC 64KS12 LIN2XLS/HS ISENSE |
| MMC2001HCAB33B | IC MCU 32BIT 33MHZ 144-LQFP |
| MMC2107CFCPU33 | IC MCU 32BIT 33MHZ 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACDWB/R2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| MM908E625ACEK | 功能描述:8位微控制器 -MCU Quad Half H-Bridge with P/S, HC08, LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。