- 您現在的位置：買賣IC網 > PDF目錄98023 > MM908E625ACDWB (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E625ACDWB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 17.90 X 7.50 MM, 0.65 MM PITCH, PLASTIC, SOIC-54 |
| 文件頁數： | 20/49頁 |
| 文件大小： | 907K |
| 代理商： | MM908E625ACDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
27
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
POWER OUTPUT REGISTER (POUT)
Current Source Select Bits (CSSEL0:CSSEL1)
These read/write bits select the current source values.
Reset clears the CSSEL0:CSSEL1 bits.
Current Source Enable Bit (CSEN)
This read/write bit enables the current source for PA1.
Reset clears the CSEN bit (Table 9).
HVDD On Bit (HVDDON)
This read/write bit enables HVDD output. Reset clears the
HVDDON bit.
1 = HVDD enabled
0 = HVDD disabled
Lamp Driver On Bit (HS_ON)
This read/write bit enables the Lamp driver. Reset clears
the HS_ON bit.
1 = Lamp driver enabled
0 = Lamp driver disabled
Hall-Effect Sensor Input Pins (H1:H3)
Function
The Hall-effect sensor input pins provide three inputs for
two-pin Hall-effect sensors for detecting stall and position or
reading Hall-effect sensor contact switches. The Hall-effect
sensor input pins are not influenced by the PSON bit in the
System Control Register.
Each pin of the Hall-effect sensor can be enabled by
setting the HxEN bit in the Hall-Effect Sensor Input Pin
Control Register (HACTL). If the pins are enabled, the Hall-
effect sensors are supplied with VSUP voltage and the sense
circuitry is working. An internal clamp circuity limits the supply
voltage to the sensor to 15 V. This sense circuitry monitors
the current to VSS. The result of this sense operation is given
by the HxF flags in the Hall-Effect Sensor Input Pin Status
Register (HASTAT).
The flag is set if the sensed current is higher than IHSCT.
To prevent noise on this flag, a hysteresis is implemented on
these pins.
After switching on the Hall-effect sensor input pins (HxEN
= 1), the Hall-effect sensors need some time to stabilize the
output. In RUN mode the software must wait at least 40
μs
between enabling the Hall-effect sensor and reading the hall
flag.
The Hall-effect sensor input pin works in an dynamic
output voltage range from VSUP down to 2.0 V. Below 2.0 V
the hallflags are not functional anymore. If the output voltage
is below a certain threshold, the Hall-Effect Sensor Input Pin
Overcurrent Flag (HP_OCF) in the System Status Register is
set.
Figures 13 through 15 illustrate the connections to the
Hall-effect input sensors.
Register Name and Address: POUT - $0b
Bits
7
6
5
4
3
2
1
0
Read
0
CSSEL1 CSSEL0 CSEN
0(16)
HVDDON HS_ON
Write
Reset
0
Notes
16.
This bit must always be set to 0.
Table 9. PA1 Current Source Enable Bit
CSEN
Current Source Enable
0
Current Source Off
1
Current Source On
相關PDF資料 |
PDF描述 |
|---|---|
| MMBD1010LT3 | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBD3000T1 | 0.2 A, SILICON, SIGNAL DIODE |
| MMBD1000LT3 | 0.2 A, SILICON, SIGNAL DIODE, TO-236AB |
| MMBD3005T1 | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD352WT3 | SILICON, UHF BAND, MIXER DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACDWB/R2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| MM908E625ACEK | 功能描述:8位微控制器 -MCU Quad Half H-Bridge with P/S, HC08, LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。