- 您現在的位置：買賣IC網 > PDF目錄359176 > MM908E625ACDWB (飛思卡爾半導體(中國)有限公司) Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication PDF資料下載
參數資料
| 型號： | MM908E625ACDWB |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 中文描述： | 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 22/48頁 |
| 文件大?。?/td> | 615K |
| 代理商： | MM908E625ACDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
22
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
LOGIC COMMANDS AND REGISTERS
INTERRUPT FLAG REGISTER (IFR
)
Hall-Effect Sensor Input Terminal Flag Bit (HPF)
This read/write flag is set depending on RUN/STOP
mode.
RUN Mode
An interrupt will be generated when a state change on any
enabled Hall-effect sensor input terminal is detected. Clear
HPF by writing a Logic [1] to HPF. Reset clears the HPF bit.
Writing a Logic [0] to HPF has no effect.
1 = State change on the hallflags detected
0 = No state change on the hallflags detected
STOP Mode
An interrupt will be generated when AWDCC is set and a
current above the threshold is detected on any enabled Hall-
effect sensor input terminal. Clear HPF by writing a Logic [1]
to HPF. Reset clears the HPF bit. Writing a Logic [0] to HPF
has no effect.
1 = One or more of the selected Hall-effect sensor input
terminals had been pulled HIGH
0 = None of the selected Hall-effect sensor input
terminals has been pulled HIGH
LIN Flag Bit (LINF)
This read/write flag is set on the falling edge at the LIN
data line. Clear LINF by writing a Logic [1] to LINF. Reset
clears the LINF bit. Writing a Logic [0] to LINF has no effect.
1 = Falling edge on LIN data line has occurred
0 = Falling edge on LIN data line has not occurred since
last clear
High-Temperature Flag Bit (HTF)
This read/write flag is set on
a
high-temperature condition.
Clear HTF by writing a Logic [1] to HTF. If a high-temperature
condition is still present while writing a Logic [1] to HTF, the
writing has no effect. Therefore, a high-temperature interrupt
cannot be lost due to inadvertent clearing of HTF. Reset
clears the HTF bit. Writing a Logic [0] to HTF has no effect.
1 = High-temperature condition has occurred
0 = High-temperature condition has not occurred
Low-Voltage Flag Bit (LVF)
This read/write flag is set on a low-voltage condition. Clear
LVF by writing a Logic [1] to LVF. If a low-voltage condition is
still present while writing a Logic [1] to LVF, the writing has no
effect. Therefore, a low-voltage interrupt cannot be lost due
to inadvertent clearing of LVF. Reset clears the LVF bit.
Writing a Logic [0] to LVF has no effect.
1 = Low-voltage condition has occurred
0 = Low-voltage condition has not occurred
High-Voltage Flag Bit (HVF)
This read/write flag is set on a high-voltage condition.
Clear HVF by writing a Logic [1] to HVF. If high-voltage
condition is still present while writing a Logic [1] to HVF, the
writing has no effect. Therefore, a high-voltage interrupt
cannot be lost due to inadvertent clearing of HVF. Reset
clears the HVF bit. Writing a Logic [0] to HVF has no effect.
1 = High-voltage condition has occurred
0 = High-voltage condition has not occurred
Overcurrent Flag Bit (OCF)
This read-only flag is set on an
overcurrent condition.
Reset clears the OCF bit. To clear this flag, write a Logic [1]
to the appropriate overcurrent flag in the SYSSTAT Register.
See
Figure 10
,illustrating the three signals triggering the
OCF.
1 = High-current condition has occurred
0 = High-current condition has not occurred
Figure 10. Principal Implementation for OCF
Register Name and Address: IFR - $05
Bits
7
6
5
4
3
2
1
0
Read
0
HPF
LINF
HTF
LVF
HVF
OCF
0
Write
Reset
0
0
0
0
0
0
0
0
OCF
HVDD_OCF
HS_OCF
HB_OCF
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E625 | Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication(集成四半H橋，帶電源、嵌入式MCU和LIN串行通信功能) |
| MM908E626AVDWB | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626R2 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MMA1200D | Surface Mount Micromachined Accelerometer(表面安裝微電機加速計) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E625ACDWB/R2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| MM908E625ACEK | 功能描述:8位微控制器 -MCU Quad Half H-Bridge with P/S, HC08, LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。