參數資料
型號： MM908E624ACDWB/R
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54
封裝： PLASTIC, SOIC-54
文件頁數： 11/34頁
文件大小： 714K
代理商： MM908E624ACDWB/R
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
908E624
Functional Description
Functional Terminal Description
Fast signal transitions on MCU terminals place high, short-
duration current demands on the power supply. To prevent
noise problems, take special care to provide power supply
bypassing at the MCU.
For details refer to the 68HC908EY16 datasheet.
ADC SUPPLY TERMINALS (VDDA AND VSSA)
VDDA and VSSA are the power supply terminals for the
analog-to-digital converter (ADC). It is recommended that a
high-quality ceramic decoupling capacitor be placed between
these terminals.
Important
VDDA is the supply for the ADC and should be
tied to the same potential as EVDD via separate traces.
VSSA is the ground terminal for the ADC and should be tied
to the same potential as EVSS via separate traces.
For details refer to the 68HC908EY16 datasheet.
ADC REFERENCE TERMINALS (VREFL AND
VREFH)
VREFL and VREFH are the reference voltage terminals for
the ADC. It is recommended that a high-quality ceramic
decoupling capacitor be placed between these terminals.
Important
VREFH is the high reference supply for the
ADC and should be tied to the same potential as VDDA via
separate traces. VREFL is the low reference supply for the
ADC and should be tied to the same potential as VSSA via
separate traces.
For details refer to the 68HC908EY16 datasheet.
TEST TERMINAL (FLSVPP)
This terminal is for test purposes only. Do not connect in
the application.
PWMIN TERMINAL
This terminal is the direct PWM input for high-side
outputs 1 and 2 (HS1 and HS2). If no PWM control is
required, PWMIN must be connected to VDD to enable the
HS1 and HS2 outputs.
LIN TRANSCEIVER OUTPUT TERMINAL (RXD)
This terminal is the output of LIN transceiver. The terminal
must be connected to the microcontroller’s Enhanced Serial
Communications Interface (ESCI) module (RXD terminal).
RESET TERMINAL (RST_A)
RST_A
is the reset output terminal of the analog die and
must be connected to the RST terminal of the MCU.
Important
To ensure proper operation, do not add any
external pullup resistor.
INTERRUPT TERMINAL (IRQ_A)
IRQ_A
is the interrupt output terminal of the analog die
indicating errors or wake-up events. This terminal must be
connected to the IRQ terminal of the MCU.
WINDOW WATCHDOG CONFIGURATION
TERMINAL (WDCONF)
This terminal is the configuration terminal for the internal
watchdog. A resistor is connected to this terminal. The
resistor value defines the watchdog period. If the terminal is
open, the watchdog period is fixed to its default value.
The watchdog can be disabled (e.g., for flash
programming or software debugging) by connecting this
terminal to GND.
POWER SUPPLY TERMINALS (VSUP1 AND
VSUP2)
This VSUP1 power supply terminal supplies the voltage
regulator, the internal logic, and LIN transceiver.
This VSUP2 power supply terminal is the positive supply
for the high-side switches.
POWER GROUND TERMINAL (GND)
This terminal is the device ground connection.
HIGH-SIDE OUTPUT TERMINALS (HS1 AND HS2)
These terminals are high-side switch outputs to drive loads
such as relays or lamps. Each switch is protected with
overtemperature and current limit (overcurrent). The output
has an internal clamp circuitry for inductive load. The HS1
and HS2 outputs are controlled by SPI and have a direct
enabled input (PWMIN) for PWM capability.
HIGH-SIDE OUTPUT TERMINAL (HS3)
This high-side switch can be used to drive small lamps,
Hall-effect sensors, or switch pullup resistors. The switch is
protected with overtemperature and current limit
(overcurrent). The output is controlled only by SPI.
LIN BUS TERMINAL (LIN)
The LIN terminal represents the single-wire bus
transmitter and receiver. It is suited for automotive bus
systems and is based on the LIN bus specification.
WAKE-UP TERMINALS (L1 AND L2)
These terminals are high-voltage capable inputs used to
sense external switches and to wake up the device from
Sleep or Stop mode. During Normal mode the state of these
terminals can be read through SPI.
相關PDF資料
PDF描述
MM908E625ACDWB 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54
MMBD1010LT3 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB
MMBD3000T1 0.2 A, SILICON, SIGNAL DIODE
MMBD1000LT3 0.2 A, SILICON, SIGNAL DIODE, TO-236AB
MMBD3005T1 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE
相關代理商/技術參數
參數描述
MM908E624ACDWBR2 功能描述:IC TRPL SWITCH MCU/LIN 54-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:- 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382
MM908E624ACEW 功能描述:開關 IC - 各種 TRIPLE HIGH SIDE SW RoHS:否 制造商:Fairchild Semiconductor 開啟電阻（最大值）: 電源電壓-最大:4.4 V 電源電壓-最小:2.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WLCSP-9 封裝:Reel
MM908E624ACEW/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Triple High Side Switch with Embedded MCU and LIN Serial Communicationfor Relay Drivers
MM908E624ACEWR2 功能描述:電源開關 IC - 配電 TRIPLE HIGH SIDE DRIVER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
MM908E624ACPEW 功能描述:8位微控制器 -MCU 3 HIGH SIDE SWITCH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*