- 您現在的位置：買賣IC網 > PDF目錄359659 > MM908E621ACDWBR2 (飛思卡爾半導體(中國)有限公司) Integrated Quad Half-Bridge and Triple High-Side with Embedded MCU and LIN for High End Mirror PDF資料下載
參數資料
| 型號： | MM908E621ACDWBR2 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Integrated Quad Half-Bridge and Triple High-Side with Embedded MCU and LIN for High End Mirror |
| 中文描述： | 綜合四半橋和三高的嵌入式微控制器和LIN高端側鏡 |
| 文件頁數： | 40/62頁 |
| 文件大?。?/td> | 540K |
| 代理商： | MM908E621ACDWBR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
40
908E621
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
Table 10. High-Side Configuration Bits
High-Side Overvoltage / Undervoltage Protection
The outputs are protected against under- / overvoltage
conditions. This protection is done by the low and high
voltage interrupt circuitry. If an over- under voltage condition
is detected (LVIF / HVIF) and Bit VIS in the High-Side Status
Register is cleared, the output is disabled.
The over- / undervoltage status flags are cleared (and the
output reenabled) by writing a logic [1] to the LVIF / HVIF
flags in the Interrupt Flag Register or by reset. Clearing this
flag has no effect as long as a high or low voltage condition
is present.
HIGH-SIDE OVERTEMPERATURE PROTECTION
The outputs are protected against over temperature
conditions.
Each power output comprises two different temperature
thresholds.
The first threshold is the high temperature interrupt (HTI),
if the temperature reach this threshold the HTI bit in the
interrupt flag register is set and an interrupt will be generated
if HTIE bit in the interrupt mask register is set. In addition this
interrupt can be used to automatically turn off the power
stages (all high-sides, on Half bridges just the high-side
FET’s). This shutdown can be enabled/disabled by Bit
HTIS0.
The high temperature interrupts flag (HTIE) is cleared (and
the outputs reenabled) by writing a logic [1] to the HTIF flag
in the Interrupt Status Register or by reset. Clearing this flag
has no effect as long as a high temperature condition is
present.
If the HTIS shutdown is disabled, a second threshold
(HTR) will be used to turn off all power stages (HB (all Fet’s),
HS, HVDD, H0) in order to protect the device.
High-Side Overcurrent Protection
The HS outputs are protected against overcurrent. When
the overcurrent limit is reached, the output will be
automatically switched off and the overcurrent flag is set.
Due to the high inrush current of bulbs a special feature
was implemented to avoid a overcurrent shutdown during this
inrush current. If a PWM frequency will be supplied to the
PWM input during the switch on of a bulb, the inrush current
will be limited to the overcurrent shutdown limit. This means,
if the current reaches the overcurrent shutdown, the high-
side will be switched off, but each rising edge on the PWM
input will enable the driver again. The duty cycle supplied by
the MCU has no influence on the switch-on time of the high-
side driver.
In order to distinguish between a shutdown due to an
inrush current or a real shutdown, the software has to check
if the overcurrent status flag (HSxOCF) in the High-Side
Status register is set beyond a certain period of time.
HSxPWM
HSxON
Mode
0
0
High-side MOSFET off
0
1
High-side MOSFET on, in case of overcurrent
the overcurrent flag (HSxOCF) is set and the
High-side MOSFET is turned off
1
0
In this mode the PWM duty cycle is either
controlled by the PWM input signal or in case
the overcurrent shutdown value is reached by
the part itself.
Without reaching the overcurrent shutdown,
the high-side driver is directly driven from the
PWM input signal. If the Input signal is high the
output is on, if low the output is off (PWM
control).
If the current reaches the overcurrent
shutdown value, the high-side will be
automatically turned off, with the next rising
edge of the PWM input signal the output will
turn on again (current limitation). The HSxOCF
bit will be set, software has to distinguish
between an inrush current and a real short on
the output.
1
1
High-side MOSFET is switched on and the
inrush current limitation is enabled, means the
high side will start automatically with an
current limitation around the overcurrent
shutdown threshold. (PWM signal must be
applied, see
Figure 24
)
If the high-side enters current limitation the
HSxOCF bit is set, but the output is not
disabled. The software needs to take care
about distinguish between an inrush current
and a real short on the output.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33996EKR2 | 16-Output Switch with SPI Control |
| MCZ33993EWR2 | Multiple Switch Detection Interface |
| MCZ146010EGR2 | Low Power CMOS Photoelectric Smoke Detector IC |
| MCZ146012EGR2 | Low Power CMOS Photoelectric Smoke Detector IC |
| MCF5211CAE66 | ColdFire Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E621ACPEK | 功能描述:8位微控制器 -MCU QUAD H-B/3-HS W/MCU & LI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E621ACPEKR2 | 功能描述:8位微控制器 -MCU QUAD HB AND TRIPLE HS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E622 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
| MM908E622_08 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge, Triple High Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
| MM908E622ACDR2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
發(fā)布緊急采購，3分鐘左右您將得到回復。