- 您現在的位置：買賣IC網 > PDF目錄98023 > MM908E621ACDWB (FREESCALE SEMICONDUCTOR INC) 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E621ACDWB |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 17.90 X 7.50 MM, 0.65 MM PITCH, PLASTIC, SOIC-54 |
| 文件頁數： | 19/62頁 |
| 文件大?。?/td> | 917K |
| 代理商： | MM908E621ACDWB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
908E621
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
OPERATING MODES OF THE MCU
For a detailed description of the operating modes of the
MCU, refer to the MC68HC908EY16 datasheet.
INTERRUPTS
The 908E621 has seven different interrupt sources. An
interrupt pulse on the IRQ_A terminal is generated to report
an event or fault to the MCU. All interrupts are maskable and
can be enabled/disabled via the SPI (Interrupt Mask
Register). After reset all interrupts are automatically disabled.
Low Voltage Interrupt
Low voltage interrupt (LVI) is related to external supply
voltage VSUP. If this voltage falls below the LVI threshold, it
will set the LVIF bit in the Interrupt Flag Register. In case the
low voltage interrupt is enabled (LVIE = 1), an interrupt will be
initiated.
During Sleep and Stop mode the low voltage interrupt
circuitry is disabled.
High Voltage Interrupt
The High voltage Interrupt (HVI) is related to the external
supply voltage VSUP. If this voltage rises above the HVI
threshold it will set the HVIF bit in the Interrupt Flag Register.
In case the High voltage Interrupt is enabled (HVIE = 1), an
interrupt will be initiated.
During Stop and Sleep mode the HVI circuitry is disabled.
High Temperature Interrupt
The high temperature interrupt (HTI) is generated by the
on chip temperature sensors. If the chip temperature is above
the HTI threshold the HTIF bit in the Interrupt Flag Register
will be set. In case the high temperature interrupt is enabled
(HTIE = 1), an interrupt will be initiated.
During Stop and Sleep mode the HTI circuitry is disabled.
LIN Interrupt
The LIN Interrupt is related to the Stop mode. If the LIN
interrupt is enabled (LINIE = 1) in Stop mode an interrupt is
asserted, if a rising edge is detected and the bus was
dominant longer than TpropWL. After the wake-up / interrupt
the LINIF is indicating the reason for the wake-up / interrupt.
Power Stage Fail Interrupt
The power stage fail flag indicates an error condition on
In case the power stage fail interrupt is enabled (PSFIE =
1), an interrupt will be initiated if:
During Stop and Sleep mode the PSFI circuitry is disabled.
HO Input Interrupt
The H0 interrupt flag H0IF is set in run mode by a state
change of the H0F flag (rising or falling edge on the enabled
Table 6. Operating Modes Overview
Device Mode
Voltage Regulator
Wake-Up Capabilities
RST_A
Output
MCU monitoring/
Watchdog
Function
Power Stages
LIN Interface
Reset
VDD ON
N/A
LOW
Disabled
Normal Request
VDD ON
N/A
HIGH
tNORMREQ (80 ms
typical) time out to
set PSON bit in
System Control
Register
Disabled
Normal (Run)
VDD ON
N/A
HIGH
Window Watchdog
active if enabled
Enabled
Stop
VDD ON with limited
current capability
LIN wake-up,
L0 state change
(SPI PSON=1)(1)
HIGH
Disabled
Recessive state with
wake-up capability
Sleep
VDD OFF
LIN wake-up
L0 state change
LOW
Disabled
Recessive state with
wake-up capability
Notes
1.
The SPI is still active in Stop mode. However, due to the limited current capability of the voltage regulator in Stop mode, the PSON
bit has to be set before the increased current caused from a running MCU causes an LVR.
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E622ACDWB/R2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E624ACDWB/R | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MM908E625ACDWB | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
| MMBD1010LT3 | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBD3000T1 | 0.2 A, SILICON, SIGNAL DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E621ACDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge and Triple High Side with Embedded MCU and LIN for High End Mirror |
| MM908E621ACDWBR2 | 功能描述:8位微控制器 -MCU QUAD HB / TRIPLE HS 841B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E621ACPEK | 功能描述:8位微控制器 -MCU QUAD H-B/3-HS W/MCU & LI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E621ACPEKR2 | 功能描述:8位微控制器 -MCU QUAD HB AND TRIPLE HS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E622 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror |
發布緊急采購，3分鐘左右您將得到回復。