![](http://datasheet.mmic.net.cn/210000/MLO81100-02120_datasheet_15452235/MLO81100-02120_1.png)
Surface Mount Voltage Controlled Oscillator
ISM 2090 - 2150 MHz
MLO81100-02120
Preliminary Specifications
V1.00
M/A-COM Ltd.
North America:
Tel. (800) 366-2266
Fax (800) 618-8883
I
Asia/Pacific: Tel. +81 3 3263-8761
Fax +81 3 3263-8769
I
Europe: Tel. +44 (1344) 869 595
Fax +44 (1344) 300 020
1
This Preliminary Specifications Data Sheet Contains Typical Electrical Specifications Which May Change Prior to Final Introduction.
Parameter
Test Conditions
Units
MHz
V
dBm
V
mA
dBc/Hz
MHz/V
Ratio
MHz
dBc
MHz/V
MHz
MHz/°C
pF
Min.
2090
+0.5
-2.0
+4.75
Typ.
Max.
2150
+4.5
+4.0
+5.25
20
-105
Frequency Range
Tuning Voltage (VT)
2
RF Output Power
3
Supply Voltage (V
CC
)
4
Supply Current (I
CC
)
Phase Noise
5
Tuning Sensitivity
Tuning Linearity
Modulation Bandwidth
Harmonic Outputs
6
Frequency Pushing
Frequency Pulling
Frequency Drift
Tune Input Capacitance
1. All specifications apply with a 50 ohm load impedance.
2. Tuning voltages shown are the minimum and maximum voltages
required to tune the frequency range including temperature effects
-20°C to +70°C. Devices will oscillate normally with tuning voltages
from 0V to +10V.
3. Output power window includes unit to unit variation, temperature
effects -20°C to +70°C and frequency flatness (typically ±0.5 dB at
any constant temperature).
2090 - 2150 MHz
+5.00
SSB at 100 KHz offset from carrier
2090 - 2150 MHz
2090 - 2150 MHz
3 dB bandwidth
-110
60
1.75
10
-10
8.0
25
VCC 4.75V to 5.25V
1.5:1 VSWR load, all phases
0.3
50
Electrical Specifications
1
,
T
A
= +25°C, V
CC
= +5V
(unless otherwise stated)
Features
Miniature Size
Surface Mount Package
Electrically Shielded
Low Phase Noise
Highly Linear Tuning
G
Description
The MLO81100-02120 is a fundamental single ended oscilla-
tor designed for use in cost sensitive wireless and telemetry
applications. The device has been optimised by careful
selection of the bipolar transistor and varactor diode for low
phase noise and high linearity tuning characteristics.
The low profile surface mount package used provides for
electrical shielding, ease of assembly and repeatable perfor-
mance. M/A-COM’s GMIC volume manufacturing techniques
together with automatic assembly and electrical testing
ensure a high degree of electrical and mechanical repeatabil-
ity at low cost and in high volume. Manufacturing is carried
out in an ISO 9000 qualified facility.
G
G
G
G
4. Devices may be operated at lower supply voltage with reduced
performance.
5. For typical phase noise at other offsets see phase noise curve.
6. No non-harmonic spurious visible when measured on a test system
with a dynamic range of 70 dB.
LCC1 Package Dimensions
5.71
3
2
1
1
4.41
5
10.12
0.635
0
1
2.03
Orientation
Mark
DETAIL A
RF
V
CC
V
T
SEE
BELOW
Tolerance is as follows:
X.X = +/- 0.500
X.XX = +/- 0.127
X.XXX = +/- 0.127
All dimensions in mm.
Pad
1
2
3
Length
2.79
2.67
2.67