![](http://datasheet.mmic.net.cn/210000/MLO82200-34125_datasheet_15452236/MLO82200-34125_1.png)
Surface Mount Voltage Controlled Oscillator
4020 - 4230 MHz
MLO82200-34125
Preliminary Specifications
V1.00
M/A-COM Ltd.
North America:
Tel. (800) 366-2266
Fax (800) 618-8883
I
Asia/Pacific: Tel. +81 (03) 3226-1671
Fax +81 (03) 3226-1451
I
Europe: Tel. +44 (1344) 869 595
Fax +44 (1344) 300 020
1
Parameters
Frequency Range
Tuning Voltage (V
T
)
2
RF Output Power
3
Supply Voltage (V
CC
)
4
Supply Current (I
CC
)
Phase Noise
5
Tuning Sensitivity
Tuning Linearity
Modulation Bandwidth
Harmonic Outputs
6
Frequency Pushing
Frequency Pulling
Frequency Drift
Tune Input Capacitance
1. All specifications apply with a 50 ohm load impedance.
2. Tuning voltages shown are the minimum and maximum voltages
required to tune the frequency range including temperature effects
-20°C to +70°C. Devices will oscillate normally with tuning voltages
from 0V to +15V.
3. Output power window includes unit to unit variation, temperature
effects -20°C to +70°C and frequency flatness (typically ±0.5 dB at
any constant temperature).
The Preliminary Specifications Data Sheet Contains Typical Electrical Specifications Which May Change Prior to Final Introduction.
Test Conditions
Units
MHz
V
dBm
V
mA
dBc/Hz
MHz/V
Ratio
MHz
dBc
MHz/V
MHz
MHz/°C
pF
Min.
4020
+1
+4.0
+11.5
Typ.
Max.
4230
+10
+8.0
+12.5
50
-100
100
2.0
4020 - 4230 MHz
+12.0
SSB at 100 KHz offset from carrier
4020 - 4230 MHz
4020 - 4230 MHz
3 dB bandwidth
10
-10
8.0
20
VCC 11.5V to 12.5V
1.5:1 VSWR load, all phases
0.35
50
Electrical Specifications
1
,
T
A
= +25°C, V
CC
= +12V (unless otherwise stated)
Features
Miniature Size
Surface Mount Package
Electrically Shielded
Low Phase Noise
Highly Linear Tuning
G
Description
The MLO82200-34125 is a fundamental single ended oscil-
lator designed for use in cost sensitive wireless and teleme-
try applications. The device has been optimised by careful
selection of the bipolar transistor and varactor diode for
low phase noise and high linearity tuning characteristics.
The low profile surface mount package used provides for
electrical shielding, ease of assembly and repeatable per-
formance. M/A-COM’s GMIC volume manufacturing tech-
niques together with automatic assembly and electrical
testing ensure a high degree of electrical and mechanical
repeatability at low cost and in high volume. Manu-
facturing is carried out in an ISO 9000 qualified facility.
4. Devices may be operated at lower supply voltage with reduced per-
formance.
5. For typical phase noise at other offsets see phase noise curve.
6. No non-harmonic spurious visible when measured on a test system
with a dynamic range of 70 dB.
LCC1 Package Dimensions
4.41
5.71
5
10.12
0.635
2.03
X.X = +/- 0.500
X.XX = +/- 0.127
X.XXX = +/- 0.127
TOLERANCE AS FOLLOWS:-
3
Orientation
Mark
Length
2.79
2.67
2.67
Pad
1
2
3
DETAIL A
1
RF
VCC
VT
SEE
BELOW
2
G
G
G
G
All dimensions in mm.