- 您現在的位置：買賣IC網 > PDF目錄385579 > ML01618 (Mitsubishi Electric Corporation) 10Gb/s EA Modulator Driver IC PDF資料下載
參數資料
| 型號： | ML01618 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | 10Gb/s EA Modulator Driver IC |
| 中文描述： | 10Gb / s的電吸收調制器驅動IC |
| 文件頁數： | 9/9頁 |
| 文件大?。?/td> | 456K |
| 代理商： | ML01618 |
MITSUBISHI ICs for Optical Communication
M L 0 X X 1 8
10Gb/s EA Modulator Driver IC
NOTIFICATION FOR BARE DIE SUPPLY (ML0CP18)
1. Quality
After the reception of bare die by the customer, performance, yield and reliability of the application of the bare die will not be
guaranteed. The supplier does not have the responsibility for field failures in the applied product.
2. Storage
a) Store in dry nitrogen.
< Before opening shipped conductive film bag (dry N2 sealed) >
Temperature
: 15 to 35 deg. C
Humidity : 45% - 75% RH
Term
: 3 months
< After opening >
Temperature
: 15 to 35 deg. C
Atmosphere
: Dry N2 gas
(The dew point should be less than -30 deg. C)
(No contact with gas including ammonia and sulfur)
Term
: The appearance of the bare die is not guaranteed after its opening.
b) Don’t apply excess vibration or shock.
3. Opening a package
a) Handle devices in clean room or on clean bench.
b) Take measures to avoid electro-static damage.
c) To open a film bag, please use scissors or a knife.
d) When taking out the devices, never touch devices barehanded. Please use clean tweezers or similar.
When use tweezers, please catch a device by side to avoid cracking or damaging the device.
Since gallium arsenide is more brittle material than silicon, special care must be taken.
4. Die bonding
The following methods are recommended for die bonding.
a) Die should be bonded lower than 300 deg. C.
b) The time duration of die bonding at maximum temperature is recommended to be shorter than 15 sec.
c) Cool down gradually, to avoid chip crack.
d) All die bonding equipment and workers should be grounded.
5. Wire bonding
The following methods are recommended for wire bonding.
a) Bonding force of wire bonding is recommended to be less than 55 grams with ultrasonic.
b) Check ultrasonic power not to damage on die and die pads.
c) Cool down gradually.
d) All wire bonding equipment and workers should be grounded.
6. Design
a) It is recommended to use this product in a hermetic sealed condition (N2 sealed).
b) It is recommended for customer to verify the performance and the qualification by customer's final product.
Especially, oscillation and noise generation might happen.
MITSUBISHI
ELECTRIC
- 9 -
Notice: This is not a final specification.
Some parametric limits are subject to change.
‘04/1/14 rev.2.1
相關PDF資料 |
PDF描述 |
|---|---|
| ML0CP18 | 10Gb/s EA Modulator Driver IC |
| ML0XX18 | 10Gb/s EA Modulator Driver IC |
| ML101J21 | MITSUBISHI LASER DIODES FOR OPTICAL INFORMATION SYSTEMS |
| ML1XX21 | MITSUBISHI LASER DIODES FOR OPTICAL INFORMATION SYSTEMS |
| ML7702 | MITSUBISHI LASER DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML016BG1PG | 制造商:HONEYWELL 制造商全稱:Honeywell Solid State Electronics Center 功能描述:High value and outstanding performance No internal elastomeric seals |
| ML016BS1PG | 制造商:HONEYWELL 制造商全稱:Honeywell Solid State Electronics Center 功能描述:High value and outstanding performance No internal elastomeric seals |
| ML016BS2PG | 功能描述:工業壓力 / 力傳感器 SST Pressure Transducers RoHS:否 制造商:Honeywell 工作壓力:0 bar to 25 bar 壓力類型:Sealed Gauge 準確性:0.25 % 輸出類型: 安裝風格:Screw 工作電源電壓:8 V to 30 V 輸出電壓:8 V to 30 V 封裝: |
| ML016PG1PG | 制造商:HONEYWELL 制造商全稱:Honeywell Solid State Electronics Center 功能描述:High value and outstanding performance No internal elastomeric seals |
| ML016PS1PG | 制造商:HONEYWELL 制造商全稱:Honeywell Solid State Electronics Center 功能描述:OEM PRESSURE TRANSDUCER |
發布緊急采購，3分鐘左右您將得到回復。