參數資料
型號： MK20DN512ZVLK10
元件分類： 微控制器/微處理器
英文描述： MICROCONTROLLER, PQFP64
封裝： 12 X 12 MM, 1.70 MM HEIGHT, 0.65 MM PITCH, PLASTIC, LQFP-64
文件頁數： 20/84頁
文件大?。?/td> 3949K
代理商： MK20DN512ZVLK10
MB95410H/470H Series
DS702-00004-1v0-E
27
■ NOTES ON DEVICE HANDLING
Preventing latch-ups
When using the device, ensure that the voltage applied does not exceed the maximum voltage rating.
In a CMOS IC, if a voltage higher than VCC or a voltage lower than VSS is applied to an input/output pin that
is neither a medium-withstand voltage pin nor a high-withstand voltage pin, or if a voltage out of the rating
range of power supply voltage mentioned in "1. Absolute Maximum Ratings" of “
TERISTICS” is applied to the VCC pin or the VSS pin, a latch-up may occur.
When a latch-up occurs, power supply current increases significantly, which may cause a component to be
thermally destroyed.
Stabilizing supply voltage
Supply voltage must be stabilized.
A malfunction may occur when power supply voltage fluctuates rapidly even though the fluctuation is within
the guaranteed operating range of the VCC power supply voltage.
As a rule of voltage stabilization, suppress voltage fluctuation so that the fluctuation in VCC ripple (p-p value)
at the commercial frequency (50 Hz/60 Hz) does not exceed 10% of the standard VCC value, and the transient
fluctuation rate does not exceed 0.1 V/ms at a momentary fluctuation such as switching the power supply.
Notes on using the external clock
When an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from subclock mode or stop mode.
■ PIN CONNECTION
Treatment of unused input pins
If an unused input pin is left unconnected, a component may be permanently damaged due to malfunctions
or latch-ups. Always pull up or pull down an unused input pin through a resistor of at least 2 k
Ω. Set an
unused input/output pin to the output state and leave it unconnected, or set it to the input state and treat it
the same as an unused input pin. If there is an unused output pin, leave it unconnected.
Power supply pins
To reduce unnecessary electro-magnetic emission, prevent malfunctions of strobe signals due to an increase
in the ground level, and conform to the total output current standard, always connect the VCC pin and the VSS
pin to the power supply and ground outside the device. In addition, connect the current supply source to the
VCC pin and the VSS pin with low impedance.
It is also advisable to connect a ceramic capacitor of approximately 0.1 F as a bypass capacitor between
the VCC pin and the VSS pin at a location close to this device.
DBG pin
Connect the DBG pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the debug mode due to noise, minimize the distance
between the DBG pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The DBG pin should not stay at “L” level after power-on until the reset output is released.
RST pin
Connect the RST pin directly to an external pull-up resistor.
To prevent the device from unintentionally entering the reset mode due to noise, minimize the distance
between the RST pin and the VCC or VSS pin when designing the layout of the printed circuit board.
The PF2/RST pin functions as the reset input/output pin after power-on. In addition, the reset output function
of the PF2/RST pin can be enabled by the RSTOE bit in the SYSC register, and the reset input function or
the general purpose I/O function can be selected by the RSTEN bit in the SYSC register.
Analog power supply
Always set the same potential to AVCC and VCC pins. When VCC is larger than AVCC, the current may flow
through the AN00 to AN07 pins.
相關PDF資料
PDF描述
MK30DN512ZVLL10 MICROCONTROLLER, PQFP64
MK10DN512ZVLK10 MICROCONTROLLER, PQFP64
MCF51AG128VLF MICROCONTROLLER, PQFP80
MK20DX256ZVLL10 MICROCONTROLLER, PQFP64
MCF51AG128VLK MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
MK20DN512ZVLL10 功能描述:ARM微控制器 - MCU KINETIS CORTEX M4 512K USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
MK20DN512ZVLQ10 功能描述:ARM微控制器 - MCU KINETIS CORTEX M4 512K USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
MK20DN512ZVLQ10R 制造商:Freescale Semiconductor 功能描述:MCU 32-bit K20 ARM Cortex M4 RISC 512KB Flash 1.8V/2.5V/3.3V 144-Pin LQFP T/R 制造商:Freescale Semiconductor 功能描述:KINETIS 512K USB - Tape and Reel 制造商:Freescale Semiconductor 功能描述:IC ARM CORTEX MCU 512KB 144LQFP 制造商:Freescale 功能描述:MCU 32-bit K20 ARM Cortex M4 RISC 512KB Flash 1.8V/2.5V/3.3V 144-Pin LQFP T/R
MK20DN512ZVMB10 制造商:Freescale Semiconductor 功能描述:KINETIS 512K - Trays 制造商:Freescale Semiconductor 功能描述:IC MCU ARM 512KB FLASH 81MAPBGA 制造商:Freescale Semiconductor 功能描述:MCU KINETIS K20 CORTEX M4 121MAP 制造商:Freescale Semiconductor 功能描述:MCU, KINETIS, K20, CORTEX M4, 121MAP 制造商:Freescale Semiconductor 功能描述:IC 32BIT MCU KINETIS K20 100MHZ 81-MAPBGA, Controller Family/Series:(ARM Cortex 制造商:Freescale Semiconductor 功能描述:IC 32BIT MCU KINETIS K20 100MHZ 81-MAPBGA, Controller Family/Series:(ARM Cortex - M4) Kinetis K20, Core Size:32bit, No. of I/O's:53, Supply Voltage Min:1.71V, Supply Voltage Max:3.6V, Digital IC Case Style:MAPBGA, No. of Pins:81 , RoHS Compliant: Yes
MK20DN512ZVMC10 功能描述:ARM微控制器 - MCU KINETIS 512K USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*