參數資料
型號： MIC5159BM6 TR
廠商： Micrel Inc
文件頁數： 8/23頁
文件大?。?/td> 471K
描述： IC REG CTRLR SGL POS ADJ SOT23-6
標準包裝： 3,000
類型： 正，可調式
輸出數： 1
輸出電壓： 可調
電流 - 電源： 10mA
輸入電壓： 1.65 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
封裝/外殼： SOT-23-6
供應商設備封裝： SOT-23-6
包裝： 帶卷 (TR)
其它名稱： MIC5159BM6TR
MIC5159BM6TR-ND
Micrel, Inc.
MIC5159
 
 
June 2006 
8
M9999-062706
 
 
 
?/DIV>
JA
 = 25.71癈/W
The heatsink and MOSFET must have a combined
thermal resistance to meet the above criteria.
The typical thermal resistance from the junction to the
case (?/DIV>
JC
) of a TO-263 (D
2
  pack) is 6癈/W. Adding
0.2癈/W for case to sink thermal resistance (?/DIV>
CS
), the
heatsink must have a sink to ambient thermal resistance
(?/DIV>
SA
) of:
 
?/DIV>
SA
 = ?/DIV>
JA
 (?/DIV>
JC
 + ?/DIV>
CS
)
 
?/DIV>
SA
 = 25.71癈/W  (6癈/W + 0.2癈/W)
 
?/DIV>
SA
 = 19.51癈/W
According to the calculations, the heatsink must have a
?/DIV>
SA
 of 19.51癈/W or better.
For a full discussion of heat sinking and thermal effects
on voltage regulators, refer to the Regulator Thermals
section of Micrels Designing with Low-Dropout Voltage 
Regulators handbook. 
Short-Circuit Current Limit
The above thermal design calculations apply to normal
operation. In the case where the P-Channel MOSFET
must survive extended periods of short-circuit current,
another   approach   for   thermal   design   must   be
considered. Due to the fact that the MIC5159 delivers
constant current limiting, power dissipated by the
MOSFET is equal to the input voltage multiplied by the
maximum output current.
Figure 1 shows a simple, inexpensive circuit that allows
the current limiting to be re-entrant. This reduces power
dissipation in current limited conditions. As the output
voltage begins to drop, the differential voltage across the
input and output increases. This pulls the current sense
voltage lower, reducing the amount of output current to
maintain 50mV across the sense resistor. This reduction
in output current equates to a reduction in power
dissipation in the MOSFET. Figures 2 and 3 show a
comparison of linear current limiting versus the re-
entrant current limiting scheme implemented in Figure 1.
MIC5159-1.8BM6/YM6
R
VOUT
R
SENSE
C1
10礔
3.3 V
IN
R
VIN
Q1,2,3
Si4433DYx3
ISENSE
VIN
GATE
ADJ
C2
47礔
1.8 V
OUT
1.5
 
Figure 1. Re-Entrant Current Limit
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
OUTPUT CURRENT (A)
Constant Current Limit
Re-Entrant
Current Limit
 
Figure 2. Output Voltage Characteristics
Re-Entrant Current Limit
 
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0
0.5
1
1.5
OUTPUT VOLTAGE (V)
Re-Entrant
Current Limiting
Constant Current
Limiting
 
Figure 3. Power Dissipation
vs. Output Voltage
Enable/Shutdown
The MIC5159 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable
pin low disables the regulator and sends it into a low off-
mode-current state. Forcing the enable pin high enables
the output voltage. This part is CMOS and the enable pin
cannot be left floating; a floating enable pin may cause
an indeterminate state on the output.
Output Capacitor
The MIC5159 requires an output capacitor to maintain
stability   and   improve   transient   response.   Proper
selection is important to ensure proper operation. The
MIC5159 output capacitor selection is highly dependent
upon the components and the application. With a very
high gate charge (gate capacitance) MOSFET, the
output requires a much larger valued ceramic capacitor
for stability. As an alternative to a large valued ceramic
capacitor, a smaller-valued tantalum capacitor can be
used to provide stability. At higher load currents, lower
R
DS(ON)
  MOSFETs are used; these MOSFETs typically
having much larger gate charge. If the application does
not require ultra-low-dropout voltage, smaller values of
ceramic capacitance may be used.
相關PDF資料
PDF描述
MIC5190BMM TR IC REG CTRLR SGL POS ADJ 10-MSOP
MIC5191BMM TR IC REG CTRLR SGL POS ADJ 10-MSOP
ML4800CP IC PFC CTRLR AVERAGE CURR 16DIP
ML4824CS2 IC PFC PWM CTRLR COMBO 16-SOIC
MX536AJCWE+ IC CONV TRUE RMS-DC 2MHZ 16SOIC
相關代理商/技術參數
參數描述
MIC5159YM6 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Programmable Current Limit μCap LDO Regulator Controller
MIC5159YM6 TR 功能描述:低壓差控制器 - LDO Progr. Ilim LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6
MIC5159YM6TR 制造商:Micrel 功能描述:LDO Regulator 1.235V to 5.5V
MIC5159YM6-TR 功能描述:Linear Regulator Controller IC Positive Adjustable 1 Output SOT-23-6 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:正，可調式 輸出數:1 電流 - 電源:10mA 電壓 - 輸入:1.65 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
MIC5162 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Dual Regulator Controller for DDR3 GDDR3/4/5 Memory and High-Speed Bus Termination
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*