- 您現在的位置：買賣IC網 > PDF目錄384736 > MIC3172YN (MICREL INC) 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C PDF資料下載
參數資料
| 型號： | MIC3172YN |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| 中文描述： | 3.5 A SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | LEAD FREE, PLASTIC, DIP-8 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 153K |
| 代理商： | MIC3172YN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁
April 2005
15
M9999-042205
MIC2172/3172
50%, the MIC2172 (and MIC3172) has a maximum duty cycle
capability of 90%. If 90% was required during operation
(start-up and high load currents), a complete reset of the
transformer during the off-time would require the voltage
across the power switch to be ten times the input voltage.
This would limit the input voltage to 6V or less for forward
converter applications.
To prevent core saturation, the application given here uses a
duty cycle limiter consisting of Q1, C4 and R3. Whenever the
MIC3172 exceeds a duty cycle of 50%, T1’s reset winding
current turns Q1 on. This action reduces the duty cycle of the
MIC3172 until T1 is able to reset during each cycle.
Fluorescent Lamp Supply
An extremely useful application of the MIC3172 is generating
an ac voltage for fluorescent lamps used as liquid crystal
display back lighting in portable computers.
Figure 15 shows a complete power supply for lighting a
fluorescent lamp. Transistors Q1 and Q2 together with ca-
pacitor C2 form a Royer oscillator. The Royer oscillator
generates a sine wave whose frequency is determined by the
series L/C circuit comprised of T1 and C2. Assuming that the
MIC3172 and L1 are absent, and the transistors’ emitters are
grounded, circuit operation is described in “Oscillator Opera-
tion.”
Oscillator Operation
Resistor R2 provides initial base current that turns transistor
Q1 on and impresses the input voltage across one half of T1’s
primary winding (Pri 1). T1’s feedback winding provides
additional base drive (positive feedback) to Q1 forcing it well
Micrel, Inc.
into saturation for a period determined by the Pri 1/C2 time
constant. Once the voltage across C2 has reached its
maximum circuit value, Q1’s collector current will no longer
increase. Since T1 is in series with Q1, this drop in primary
current causes the flux in T1 to change and because of the
mutual coupling to the feedback winding further reduces
primary current eventually turning Q1 off. The primary wind-
ings now change state with the feedback winding forcing Q2
on repeating the alternate half cycle exactly as with Q1. This
action produces a sinusoidal voltage wave form; whose
amplitude is proportional to the input voltage, across T1’s
primary winding which is stepped up and capacitively coupled
to the lamp.
Lamp Current Regulation
Initial ionization (lighting) of the fluorescent lamp requires
several times the ac voltage across it than is required to
sustain current through the device. The current through the
lamp is sampled and regulated by the MIC3172 to achieve a
given intensity. The MIC3172 uses L1 to maintain a constant
average current through the transistor emitters. This current
controls the voltage amplitude of the Royer oscillator and
maintains the lamp current. During the negative half cycle,
lamp current is rectified by D3. During the positive half cycle,
lamp current is rectified by D2 through R4 and R5. R3 and C5
filter the voltage dropped across R4 and R5 to the MIC3172’s
feedback pin. The MIC3172 maintains a constant lamp
current by adjusting its duty cycle to keep the feedback
voltage at 1.24V. The intensity of the lamp is adjusted using
potentiometer R5. The MIC3172 adjusts its duty cycle
accordingly to bring the average voltage across R4 and R5
back to 1.24V.
D3
1N5819
MIC3172
V
IN
V
SW
FB
COMP
C1
22μF
C3
1μF
R2
1k
V
5V, 1A
R4
3.74k
1%
R5
1.24k
1%
C5
470μF
L1 100μH
V
IN
12V
EN
GND
P1 P2 S
T1
1:1:1
Enable
Shutdown
D4
1N5819
D2
1N5819
* Voltage clipper
Duty cycle limiter
D1*
C2*
Q1
C4
R3
R1*
Figure 14. 12V to 5V Forward Converter
相關PDF資料 |
PDF描述 |
|---|---|
| MIC3287 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287-24YD6 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287-24YML | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287YD5 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3775-1.5BMM | 750mA UCap Low-Voltage Low-Dropout Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC3201 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High Brightness LED Driver with High-Side Current Sense |
| MIC3201_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High Brightness LED Driver with High-Side Current Sense |
| MIC3201YME | 功能描述:LED照明驅動器 HBLED Driver with High-Side Current Sense RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MIC3201YME EV | 制造商:Micrel Inc 功能描述: |
| MIC3201YME TR | 功能描述:LED照明驅動器 HBLED Driver with High-Side Current Sense RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。