- 您現在的位置：買賣IC網 > PDF目錄384736 > MIC3172YN (MICREL INC) 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C PDF資料下載
參數資料
| 型號： | MIC3172YN |
| 廠商： | MICREL INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| 中文描述： | 3.5 A SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | LEAD FREE, PLASTIC, DIP-8 |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 153K |
| 代理商： | MIC3172YN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁
MIC2172/3172
V
OUT
= required output voltage
V
F
= D1 forward voltage drop
For the example in figure 11.
I
OUT
= 0.14A
I
CL
= 1.147A
V
IN
= 4.75V (minimum)
δ
= 0.623
V
OUT
= 12.0V
V
F
= 0.6V
Then:
1.147
Micrel, Inc.
M9999-042205
12
April 2005
I
OUT
≤
I
OUT
0.141A
This value is greater than the 0.14A output current require-
ment so we can proceed to find the inductance value of L1.
2
×
4.75
×
0.623
12
(2)
L1
≤
V
IN
δ
2 P
OUT
f
SW
(
)
2
Where:
P
OUT
= 12
×
0.14 = 1.68W
f
SW
= 1
10
5
Hz (100kHz)
For our practical example:
L1
≤
I
L1
26.062
H (use 27
H)
Equation (3) solves for L1’s maximum current value.
4.75
0.623
2
168
1
10
5
(
)
2
(3)
I
L1(peak)
=
V
IN
T
ON
Where:
T
ON
=
δ
/ f
SW
= 6.23
×
10
-6
sec
I
L1(peak)
=
4.75
6.23
×
10
-6
I
L1(peak)
= 1.096A
Use a 27
μ
H inductor with a peak current rating of at least
1.4A.
Flyback Conversion
Flyback converter topology may be used in low power appli-
cations where voltage isolation is required or whenever the
input voltage can be less than or greater than the output
voltage. As with the step-up converter the inductor (trans-
former primary) current can be continuous or discontinuous.
Discontinuous operation is recommended.
Figure 12 shows a practical flyback converter design using
the MIC3172.
L1
27
×
10
-6
Switch Operation
During Q1’s on time (Q1 is the internal NPN transistor—see
block diagrams), energy is stored in T1’s primary inductance.
During Q1’s off time, stored energy is partially discharged into
C4 (output filter capacitor). Careful selection of a low ESR
capacitor for C4 may provide satisfactory output ripple volt-
age making additional filter stages unnecessary.
C1 (input capacitor) may be reduced or eliminated if the
MIC3172 is located near a low impedance voltage source.
Output Diode
The output diode allows T1 to store energy in its primary
inductance (D2 nonconducting) and release energy into C4
(D2 conducting). The low forward voltage drop of a Schottky
diode minimizes power loss in D2.
Frequency Compensation
A simple frequency compensation network consisting of R3
and C2 prevents output oscillations.
High impedance output stages (transconductance type) in
the MIC2172/3172 often permit simplified loop-stability solu-
tions to be connected to circuit ground, although a more
conventional technique of connecting the components from
the error amplifier output to its inverting input is also possible.
Voltage Clipper
Care must be taken to minimize T1’s leakage inductance,
otherwise it may be necessary to incorporate the voltage
clipper consisting of D1, R4, and C3 to avoid second break-
down (failure) of the MIC3172’s power NPN Q1.
Enable/Shutdown
The MIC3172 includes the enable/shutdown feature. When
the device is shutdown, total supply current is less than 1
A.
This is ideal for battery applications where portions of a
system are powered only when needed. If this feature is not
required, simply connect EN to V
IN
or to a TTL high voltage.
Discontinuous Mode Design
When designing a discontinuous flyback converter, first de-
termine whether the device can safely handle the peak
primary current demand placed on it by the output power.
Equation (8) finds the maximum duty cycle required for a
given input voltage and output power. If the duty cycle is
greater than 0.8, discontinuous operation cannot be used.
(8)
δ
≥
2 P
OUT
I
CL
V
IN(min)
For a practical example let:
P
OUT
= 5.0V
0.25A = 1.25W
V
IN
= 4.0V to 6.0V
I
CL
= 1.25A when
< 50%
0.833 (2 –
δ
) when
δ
≥
50%
相關PDF資料 |
PDF描述 |
|---|---|
| MIC3287 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287-24YD6 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287-24YML | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3287YD5 | 1.2MHz PWM White LED Driver with OVP in Thin SOT-23 and 2mm x 2mm MFL |
| MIC3775-1.5BMM | 750mA UCap Low-Voltage Low-Dropout Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC3201 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High Brightness LED Driver with High-Side Current Sense |
| MIC3201_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:High Brightness LED Driver with High-Side Current Sense |
| MIC3201YME | 功能描述:LED照明驅動器 HBLED Driver with High-Side Current Sense RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MIC3201YME EV | 制造商:Micrel Inc 功能描述: |
| MIC3201YME TR | 功能描述:LED照明驅動器 HBLED Driver with High-Side Current Sense RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。