- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33884EG (飛思卡爾半導體(中國)有限公司) Switch Monitor Interface PDF資料下載
參數資料
| 型號： | MCZ33884EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Switch Monitor Interface |
| 中文描述： | 開關顯示器接口 |
| 文件頁數： | 15/21頁 |
| 文件大小： | 251K |
| 代理商： | MCZ33884EG |
Analog Integrated Circuit Device Data
Freescale Semiconductor
15
33884
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
TRI-STATE COMMAND
This command places an external switch into a Tri-State
condition, essentially disconnecting the wetting current (if the
switch is metallic) and the sustain current. The internal input-
threshold comparator is still internally connected to its
external pin. This command does not change the mode of
operation
CP[4:1] – CONFIGURE PROGRAMMABLE SWITCH
Configure the programmable inputs SP[4:1] to detect
either an external switch-to-ground (internal current source)
or an external switch-to-battery (internal current sink).
Note: This configuration may be entered in any of the three
valid Operating Modes (see MOD[2:1]) within the Run
command.
(e.g., a Tri-State command received while in the Polling
mode leaves the part in that mode).
Note: The Tri-State register clears all bits to logic [0] (all
inputs in Tri-State) in response to a hardware reset; all inputs
also remain in Tri-State after existing the Sleep mode.
METALLIC COMMAND
This command enables the pulsed wetting current for an
external metallic switch and disables it for an external non-
metallic switch. This command does not change the mode of
operation (e.g., a Metallic command received while in Polling
mode leaves the part in that mode). Note that the Run
register values are unknown after exiting the Sleep mode.
Table 11. Programmable Switch Bit Definition
CPx
External Switch to:
0
Ground
1
Battery
Table 12. Tri-State Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Tri-State
0
0
1
1
TG6
TG5
TG4
TG3
TG2
TG1
TP4
TP3
TP2
TP1
TB2
TB1
Reset Values:
Run Register
—
—
—
—
0
0
0
0
0
0
0
0
0
0
0
0
TG[6:1] = Tri-state switch-to-ground
TB[2:1] = Tri-state switch-to-battery
TP[4:1] = Tri-state programmable switch
Table 13. Programmable Switch Bit Definition
TGx, TBx, TPx
Input Configured to:
0
Input Disabled (Default)
1
Input Enabled
Table 14. Metallic Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Metallic
0
1
0
1
MG6
MG5
MG4
MG3
MG2
MG1
MP4
MP3
MP2
MP1
MB2
MB1
Reset Values:
Run Register
—
—
—
—
U
U
U
U
U
U
U
U
U
U
U
U
U = Unknown value coming out of Sleep mode. It must be configured with Run command.
MG[6:1] = Metallic switch-to-ground
MB[2:1] = Metallic switch-to-battery
MP[4:1] = Metallic programmable switch
Table 15. Metallic Switch Bit Definition
MGx, MBx, MPx
Accept Switch Type:
0
Non-Metallic
1
Metallic (Enable Wetting Current Pulse)
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33887EK | 5.0 A H-Bridge with Load Current Feedback |
| MCZ33889BEG | System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33927EK | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33884EG | 制造商:Freescale Semiconductor 功能描述:SWITCH MONITOR INTERFACE 24SOIC |
| MCZ33884EGR2 | 功能描述:多路器開關 IC SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
| MCZ33887EK | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33887EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33887EKR2DH | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:5.0 A H-Bridge with Load Current Feedback |
發布緊急采購，3分鐘左右您將得到回復。