- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33800EK (飛思卡爾半導體(中國)有限公司) Engine Control Integrated Circuit PDF資料下載
參數資料
| 型號： | MCZ33800EK |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Engine Control Integrated Circuit |
| 中文描述： | 發動機控制集成電路 |
| 文件頁數： | 17/39頁 |
| 文件大小： | 461K |
| 代理商： | MCZ33800EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
17
33800
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
Power On Reset (POR). All internal registers will be placed in
the reset state. The device has an Internal 100 k
resistor
pull down on the ENABLE pin.
PULSE WIDTH MODULATION (PWM)
The PWM pins are control input pins for the MOSFET pre-
drivers. The PWM pins provide parallel control and can be
programmed for an OR function with the SPI bit or an AND
function with the SPI bit (See
Table 12, on page 25
for SPI
message detail). Each PWM input pin has an internal 15
μ
A
pull down current source. The current sources are active
when the device is in Normal Mode.
DRAIN VOLTAGE SENSE (VDSNSX)
The VDSNSx pin has multiple functions for control and
diagnostics of the external MOSFET:
1. By monitoring the drain voltage of the external device,
short circuits and open circuits are detected. The filter
timer and threshold voltage are easily programmed
through SPI (see
Table 10, on page 23
and
Table 11,
on page 24
for SPI messages).
2. The VDSNSx pins are use to determine the external
load resistance. Further information is provided in the
Device Operation section of this specification.
3. The VDSNSx pins provide a drain to gate clamp for
fast turn off of inductive loads and MOSFET protection.
GATE DRIVER OUTPUTS (GDX)
The GDX pins are the gate drive outputs for an external
MOSFETS. Internal to the device is a Gate to Source resistor
designed to hold the external MOSFET in the OFF state while
the device is in POR.
INPUTS (P1, P3, P5, P7)
The input pins for octal serial switch outputs 1,3,5,7. Each
input control pin has an internal pull down current source.
Two outputs may be controlled in parallel using the PX pins
(
See Functional Device Operation on page 25
).
VOLTAGE CALIBRATED INPUT (VCAL)
The Voltage calibrated input (VCAL) provides the IC with
a reference voltage for analog circuits. VCAL (EXT or INT)
must be applied for the CCD1 and CCD2 constant current
controllers and Load Resistance measurement function to
operate. For applications where measurements are not
critical, the VCAL pin may grounded and an internally
generated reference will be used. Using the internally
generated reference will add
±
10% to all tolerances in the
parametric table.
LOAD RESISTANCE FEEDBACK (LRFDBK)
The LRFDBK pin is an operational amplifier output. The
amplifier output voltage is proportional to the load resistance
for the selected channel. The channel is selected via the SPI.
DEFAULT
The DEFAULT input controls the operation of each driver
to a Default Mode. The DEFAULT input must be logic 0 for full
function of all output drivers. For more information on the
DEFAULT operation (
See Functional Device Operation on
page 19
).
With the DEFAULT pin HIGH, the device is placed in
Default Mode. The DEFAULT pin is pulled up to the VDD
supply through an active pull up current source. In Default
Mode the device operates in the following manner:
1. OSS outputs are disabled.
2. CCD1 and CCD2 outputs are disabled.
3. SPI ON/OFF control of GATE DRIVE (GD1 to GD6)
outputs and on board PWM controllers are disabled. PWMx
input control is enabled.
In the Default Mode the device retains all register
information and output status information. Normal operation
will resume when the DEFAULT pin transitions low again and
the device will operate as programmed prior to Default Mode.
RESISTOR EXTERNAL REFERENCE (REXT)
The reference current is used in the equation to calculate
the load resistance of the PWM outputs. The load resistance
measurement current is inversely proportional to REXT
current. The resistor value may be changed to adjust the load
measurement current. A 24
resistor to ground sets the
LRFDBK output to 260mV/
.
EXPOSED PAD
The silicon die is epoxy attached to the top side of the pad.
Although the device does not use the pad for electrical
conduction, the bottom side exposed pad of the package
should be grounded.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33879AEK | Configurable Octal Serial Switch with Open Load Detect Current Disable |
| MCZ33880EG | Configurable Octal Serial Switch with Serial Peripheral Interface I/O |
| MCZ33883EG | H-Bridge Gate Driver IC |
| MCZ33884EG | Switch Monitor Interface |
| MCZ33887EK | 5.0 A H-Bridge with Load Current Feedback |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
| MCZ33810EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。